Bedienungsanleitung DeWalt D28492(K) (Seite 24 von 105) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

446565

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

ENGLISH

Do not cut or grind light metal with a

magnesium content exceeding 80%

since this type of metal is ﬂ ammable.

● Do not use any accessories other than ﬁ bre

reinforced grinding and cutting discs.

● Use only plain or depressed-centre grinding

and cutting discs.

● Use the grinding and cutting discs recommended

by the manufacturer only.

● The max. allowable speed of the grinding wheel

or cutting disc, or any other suitable accessory,

must always be equal to or greater than the

no-load speed of the tool speciﬁ ed on the

nameplate.

● Do not cut workpieces requiring a maximum

depth of cut exceeding that of the cutting disc.

● Do not use grinding and cutting discs that do

not conform to the dimensions stated in the

technical data. Do not use any spacers to make

a disc ﬁ t onto the spindle. Do not separate

reducing bushings or adapters to adapt large-

hole abrasive wheels.

● Inspect grinding and cutting discs before each

use. Do not use chipped, cracked or otherwise

defective discs.

● If provided, ensure that blotters are used when

the disc is ﬁ tted onto the spindle.

● When applying a threaded hole disc, ensure that

the thread is long enough to accept the spindle.

● Ensure that the grinding or cutting disc is

mounted correctly before use.

● Let the tool run at no-load in a safe position for

at least 30 seconds. If there is a considerable

vibration or if any other defect occurs, stop the

tool and check it to determine the cause.

● Do not operate this tool without the guard in place.

● Check that the workpiece is properly supported.

● Do not operate the tool near ﬂ ammable liquids,

gases or dust. Sparks or hot chips from cutting

or arcing motor brushes may ignite combustible

materials.

● Do not operate the tool while standing in line

with the disc. Keep other persons away from

the work area.

● Do not use cutting discs for side grinding.

● Do not operate the spindle lock while the tool is

running.

● Beware that after switching off the tool the

wheel continues to rotate for a short period.

● Always store grinding and cutting discs

in a dry place.

Labels on tool

The following pictographs are shown on the tool:

Read the instruction manual before use

Wear safety glasses

Wear ear protection

Package contents

The package contains:

1 Angle grinder

1 Guard

1 Side handle

1 Flange set

1 Two-pin spanner

1 Kitbox (K-models only)

1 Instruction manual

1 Exploded drawing

● Check for damage to the tool, parts or

accessories which may have occurred during

transport.

● Take the time to thoroughly read and

understand this manual prior to operation.

Description (ﬁ g. A)

Your angle grinder D28490/D28491/D28492(K)/

D28493 has been designed for professional

grinding and cutting applications.

1 On/off switch

2 Locking switch (not for France)

3 Unlocking switch

4 Spindle lock

5 Guard

6 Side handle

Electrical safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D28492(K) Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info