Bedienungsanleitung DeWalt D28720 T 1 (Seite 10 von 28) (Englisch, Französisch)

548823

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENGLISH

Spark Deﬂ ector Adjustment (ﬁ g. 1)

To best deflect sparks away from surrounding

persons and materials, loosen the screw (b), adjust

the spark deflector (c) and then retighten screw. Do

not allow cordset to come into contact with deflector

or sparks as damage to cordset may occur.

Depth Stop (ﬁ g. 1)

Depth stop is set at the factory for a new 355mm

(14") wheel to prevent wheel from cutting into the

supporting surface. To allow more depth of cut, use

the flat wrench provided (g) to loosen the depth stop

bolt (m) and raise bolt to desired height and then

turn jam nut m) clockwise until seated firmly on the

casting. Securely tighten the depth stop bolt before

use.

CAUTION: When changing to a

new wheel, readjust depth stop to

original position to prevent cutting into

supporting surface.

Trigger Switch (ﬁ g. 1)

To start the tool, depress the trigger switch (n). To

turn the tool off, release the trigger switch. Keep

hands and material from wheel until it has coasted

to a stop.

To prevent unauthorized use of tool, install a

standard padlock (not included) into the padlock

hole (o) located in the trigger.

Material Clamping and Supporting

(ﬁ g. 2, 3)

• Angles are best clamped and cut with both legs

resting against base.

• A spacer block slightly narrower than the

workpiece can be used to increase wheel

utilization (fig. 2).

• Long workpieces must be supported by a block

so it will be level with top of base (fig. 3). The

cut off end should be free to fall downward to

avoid wheel binding.

Vise Operation (ﬁ g. 4)

The vise (f) has a quick-travel feature. To release

the vise when it is clamped tightly, turn the crank

(h) counterclockwise one or two times to remove

clamping pressure. Lift vise lever (i) up. Pull crank

assembly out as far as desired. Vise may be pushed

forward into work without cranking. Lower vise lever

(i) then tighten vise (f) on work by using crank (h).

Fence Operation (ﬁ g. 5, 6)

The fence (e) can be adjusted two ways: to change

desired cutting angle and to change spacing

between the fence and vise.

TO CHANGE THE DESIRED CUTTING ANGLE

Use the wrench provided to loosen (do not

remove) the two fence bolts (p). Align the desired

angle indicator line with the slot line (q) in the base

(d). Securely tighten both fence bolts before use.

For more accurate square cuts, disconnect the

power supply, loosen the two fence bolts, push arm

down until wheel extends into base. Place a square

against the wheel and adjust fence against the

square. Securely tighten both fence bolts before use.

When making a miter cut, the vise (f) may not

clamp securely, depending on the thickness of the

workpiece and the miter angle. Other aids (such as

spring, bar or C-clamps) will be necessary to secure

the workpiece to the fence when making these cuts.

TO CHANGE SPACING BETWEEN THE FENCE AND VISE

Using the wrench provided, loosen and remove

the two fence bolts (p). Adjust the fence (e) to

desired locations. Insert both fence bolts in provided

locations. Securely tighten both fence bolts before

use.

Removal and Installation of Wheels

(ﬁ g. 1, 7, 8)

WARNING: Turn off and unplug the

tool before making any adjustments

or removing or installing

attachments or accessories. Be

sure the trigger switch is in the OFF

position. Do not make any adjustment

while the wheel is in motion. Do not

make any adjustment while chop saw is

plugged into power supply.

1. Push in wheel lock lever (l) and rotate wheel

(j) by hand until wheel lock lever engages slot

in inside flange (r) to lock wheel. Loosen the

bolt (s) counterclockwise in the center of the

abrasive wheel with the included flat wrench (g).

Bolt has right-hand thread.

2. Remove the bolt (s), washer (t), outside flange

(u) and old wheel(j).

3. Make sure flange surfaces are clean and flat.

Install the new abrasive wheel by reversing the

above steps.

4. Do not overtighten bolt.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D28720 T 1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt D28720 T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info