Bedienungsanleitung DeWalt D51275K T 3 (Seite 24 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546463

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

• To drive several nails: Pull the trigger first, and

then push the contact trip repeatedly against the

work surface.

Do not keep the trigger depressed when

the tool is not in use. Keep the trigger

lock-off switch rotated to the right to

prevent accidental actuation when the

tool is not in use.

Clearing a jammed nail (fig. E)

If a nail becomes jammed in the nosepiece, follow

these instructions to remove the nail:

• Disconnect the airline from the tool.

• Lock the trigger with the trigger lock-off switch.

• Lock the nail pusher (11) in the back position.

• Flip up the front latch (12) and move the bracket

(13) out of the way so that barrel (14) can be

opened.

• Remove the bent nail, using pliers if necessary.

• If the driver blade is in the down position, push

the driver blade upward using a screwdriver.

• Close the barrel (14) and put the bracket (13)

back in position.

• Press the front latch (12) into the locked position.

• Connect the air hose to the fitting on the tool.

• Load nails into the magazine. See “Loading the

tool”.

• Unlatch the nail pusher by pushing forward and

carefully slide the nail pusher forward to press

against the nails.

If nails become jammed in the nosepiece

frequently, have the tool serviced by an

authorised DEWALT service centre.

Depth setting (fig. F)

Always disconnect the tool from the air

supply before adjusting the depth setting.

The depth that the nails are driven can be adjusted

using the depth adjustment on the nosepiece of

the tool.

• To reduce the depth, press the adjustment

button (15) and slide the slider switch (16)

downward.

• To increase the depth, press the adjustment

button (15) and slide the slider switch (16)

upward.

Belt/rafter hook

These tools have an integrated belt/rafter hook.

The hook can be rotated to either side of the tool

and can be folded out of the way when not in use.

To remove the belt/rafter hook:

• Remove the air hose from the fitting on the tool.

• Use pliers or a wrench to remove the nut for the

belt/rafter hook from the end cap of the tool.

• Remove the belt/rafter hook, washer and detent

spring.

Maintenance

Your DEWALT tool has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends on proper tool care and regular cleaning.

Perform the following maintenance operations every

day:

Lubricate tool with 5-7 drops of DEWALT

pneumatic tool oil

• Insert drops into the air fitting on the end cap of

the tool.

Drain all condensation from the air compressor

tanks and hoses

• Open petcocks or other drain valves on the

compressor tanks.

• Allow any accumulated water to drain from hoses.

Clean magazine, pusher, and contact trip

mechanism

• Clean by blowing with compressed air.

Ensure that all fasteners on the tool are tight and

undamaged

• Tighten loose fasteners using the appropriate tool.

D51256.P65 28-12-2001, 09:2124

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D51275K T 3 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info