Bedienungsanleitung DeWalt D51845 T 3 (Seite 22 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546480

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

8 Use appropriate tool

The intended use is described in this instruction

manual. Do not force small tools or attachments

to do the job of a heavy-duty tool. The tool will

do the job better and safer at the rate for which it

was intended.

Warning! The use of any accessory or

attachment or performance of any operation with

this tool, other than those recommended in this

instruction manual may present a risk of personal

injury.

9 Maintain tools with care

Keep the tools in good condition and clean for

better and safer performance. Follow the

instructions for maintenance and changing

accessories. Keep all controls dry, clean and free

from oil and grease.

10 Check for damaged parts

Before using the tool, carefully check it for damage

to ensure that it will operate properly and perform

its intended function. Check for misalignment

and seizure of moving parts, breakage of parts

and any other conditions that may affect its

operation. Have damaged guards or other

defective parts repaired or replaced as instructed.

11 Have your tool repaired by an authorized

DEWALT repair agent

This tool is in accordance with the relevant safety

regulations. To avoid danger, tools must only be

repaired by qualified technicians.

Additional safety instructions for pneumatic nailers

• Always wear safety glasses.

• Always wear ear protection.

• Only use fasteners of the type specified in

the manual.

• Do not use any stands for mounting the tool to

a support.

• Never use the tool for any other purpose than

specified in this manual.

• Prior to each operation check that the safety and

triggering mechanism is functioning properly and

that all nuts and bolts are tight.

• Use quick-action couplings for connection to the

compressed air system. The non-sealable nipple

must be fitted to the tool in such a way that no

compressed air remains in the tool after

disconnection.

• Always use clean, dry compressed air.

Do not use oxygen or combustible gases as an

energy source for this tool.

• Only connect this tool to an air supply where the

maximum allowable pressure of the tool cannot

be exceeded by more than 10%. In case of

higher pressures, a pressure reducing valve

including a downstream safety valve shall be built

into the compressed air supply.

• Only use hoses with a rating exceeding the

maximum operating pressure of the tool.

• Before transporting the tool, disconnect it from

the compressed air system, especially where

ladders are used or where unusual physical

posture is adopted while moving.

• Disconnect the tool from the air supply when it is

not in use.

• Avoid weakening or damaging the tool,

for example by:

- punching or engraving

- modifications not authorised by the manufacturer

- guiding against templates made of hard

material such as steel

- dropping or pushing across the floor

- applying excessive force of any kind

• Do not use the equipment as a hammer.

• Never point any operational fastener driving tool

at yourself or at any other person.

• While working, hold the tool in such a way that

no injuries can be caused to the head or to the

body in the event of a possible recoil due to a

disruption in the energy supply or hard areas

within the workpiece.

• Never actuate the fastener driving tool into free

space.

• In the work area, carry the tool at the workplace

using only one handle, and never with the trigger

actuated.

• Consider the conditions in the work area.

Fasteners can penetrate thin workpieces or slip

off corners and edges of the workpiece, and thus

put people at risk.

• Do not drive fasteners close to the edge of the

workpiece.

• Do not drive fasteners on top of other fasteners.

• Only use spare parts specified by the

manufacturer or his authorised agents.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D51845 T 3 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info