Bedienungsanleitung DeWalt D51855 (Seite 30 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546482

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

ENGLISH

Loading the Tool (ﬁ g. 4)

WARNING: Keep the tool pointed

away from yourself and others. Serious

personal injury may result.

WARNING: Never load nails with

the contact trip or trigger activated.

Personal injury may result.

1. Lock OFF trigger.

2. Disconnect the air supply from the tool.

3. Pull the door latch (o) to open the door (p).

4. Rotate the canister door (q) open.

5. Adjust the nail platform (r) to properly

accommodate the nail length being used.

Pull up on the nail platform (r) for shorter nails.

Push in the nail platform adjustment button (

and push down on the nail platform (r) for longer

nails.

6. Place the coil on the nail platform (r).

7. Uncoil enough nails [approximately 3" (8cm)] to

reach the nose of the tool.

8. Insert the first nail into the nose and the

second nail between the two rails of the feed

pawl(t).

NOTE: Be careful not to deform the coil of nails

during the loading process. Otherwise, the nail

guide door will not close and the nails might not

feed consistently.

9. Close the canister door (q) completely.

10. Close the door (p) making sure the door latch

(o) is completely engaged.

Depth Setting (ﬁ g. 5)

WARNING: To reduce risk of serious

injury from accidental actuation when

attempting to adjust depth, ALWAYS:

• Lock OFF trigger.

• Disconnect air supply.

• Avoid contact with trigger during

adjustments.

The depth that the fastener is driven can be adjusted

using the depth adjustment next to the trigger of the

tool.

1. To drive the nail shallower, rotate the depth

setting wheel (g) to the right.

2. To drive a nail deeper, rotate the depth setting

wheel (g) to the left.

Clearing a Jammed Nail (ﬁ g. 4)

If a nail becomes jammed in the nosepiece, keep

the tool pointed away from you and follow these

instructions to clear:

1. Lock OFF trigger.

2. Disconnect the air supply from the tool.

3. Open the door (p).

4. Open the canister door (q).

5. Remove the jammed nail.

6. Correct any deformation that may have

occurred to the nail coil.

NOTE: Should nails continue to jam frequently in

nosepiece, have tool serviced by an authorised

EWALT service center.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, lock off trigger, disconnect air

line from tool and remove fasteners

from canister before making

adjustments, or personal injury may

result.

Perform the following maintenance

operations every day:

Lubrication

Lubricate tool with 10 –15 drops of DEWALT

pneumatic tool oil.

Insert drops into the air fitting on the end cap of the

tool.

Drain all condensation from the air

compressor tanks and hoses

• Open petcocks or other drain valves on the

compressor tanks.

• Allow any accumulated water to drain from

hoses.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D51855 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info