Bedienungsanleitung DeWalt D712N (Seite 29 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546145

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH

MITRE LOCK/DETENT ROD ADJUSTMENT (FIG. H)

If the base of the saw can be moved while the mitre lever (4) is locked,

the mitre lock/detent rod (56) must be adjusted.

• Unlock the mitre lever (4).

• Fully tighten the mitre lock/detent rod (56) using a screwdriver (57).

Then loosen the rod a quarter of a turn.

• Check that the table does not move when the lever (4) is locked at

a random (not preset) angle.

CHECKING AND ADJUSTING THE BLADE TO THE TABLE (FIG. I1–I4)

• Loosen the bevel clamp handle (11).

• Press the saw head to the right to ensure it is fully vertical and

tighten the bevel clamp handle.

• Pull down the head until the blade just enters the saw kerf (51).

• Place a set square (52) on the table and up against the blade (47)

(fig. I2).

Do not touch the tips of the blade teeth with the square.

• If adjustment is required, proceed as follows:

• Loosen the bevel clamp handle (11) and turn the vertical position

adjustment stop screw (28) in or out until the blade is at 90° to the

table as measured with the square.

• If the bevel pointer (58) does not indicate zero on the bevel scale

(10), loosen the screw (59) that secures the pointer and move the

pointer as necessary.

ADJUSTING THE FENCE (FIG. J1, J2)

The upper part of the left side of the fence can be adjusted to the left to

provide clearance, allowing the saw to bevel to a full 48° left. To adjust

the fence (3):

• Loosen the plastic knob (29) and slide the fence to the left.

• Make a dry run with the saw switched off and check for clearance.

Adjust the fence to be as close to the blade as practical to provide

maximum workpiece support, without interfering with the up and

down movement of the arm.

• Tighten the knob securely.

The guide groove (60) can become clogged with sawdust.

Use a stick or some low pressure air to clear the guide

groove.

The moveable part of the right side of the fence can be adjusted to

provide maximum support of the workpiece near the blade, while

allowing the saw to bevel to a full 45° left. The sliding distance is limited

by stops in both directions.

To adjust the fence (8):

• Loosen the wing nut (76) to release the fence (8).

• Slide the fence to the left.

• Make a dry run with the saw switched off and check for clearance.

Adjust the fence to be as close to the blade as practical to provide

maximum workpiece support, without interfering with the up and

down movement of the arm.

• Tighten the wing nut (76) to secure the fence in place.

OVERRIDING THE BEVEL STOPS (FIG. K)

The bevel stops facilitate the setting of the saw blade in the vertical

position and the 45° bevel position. By overriding the bevel stops, bevel

angles can be achieved from 2° right to 48° left.

• To override the bevel stops, first release the saw head and push

it slightly to the left, then pull out the override knob (27) and turn

it into the override position (62). The override knob automatically

clicks in place.

• Set the required bevel angle and secure the head in this position.

• To discontinue the override, turn the override knob (27) back into

the bevel stop position (61).

CHECKING AND ADJUSTING THE BEVEL ANGLE (FIG. A1, A2 & I5)

• Make sure the override knob (27) is located in the bevel stop

position.

• Loosen the left side fence clamping knob (29) and slide the upper

part of the left side fence to the left as far as it will go.

• Loosen the bevel clamp handle (11) and move the saw head to the

left. This is the 45° bevel position.

• If adjustment is required, proceed as follows:

• Turn the stop screw (9) in or out as necessary until the pointer (58)

indicates 45°.

RAIL GUIDE ADJUSTMENT (FIG. L)

• Regularly check the rails for clearance.

• To reduce clearance, gradually rotate the set screw (64) clockwise

while sliding the saw head back and forth. Instructions for use

Instructions for Use

Always observe the safety instructions and applicable

regulations.

The attention of UK users is drawn to the “woodworking machines

regulations 1974” and any subsequent amendments.

Prior to Operation

• Install the appropriate saw blade. Do not use excessively worn

blades. The maximum rotation speed of the tool must not exceed

that of the saw blade.

• Do not attempt to cut excessively small pieces.

• Allow the blade to cut freely. Do not force.

• Allow the motor to reach full speed before cutting.

• Make sure all locking knobs and clamp handles are tight.

• Secure the workpiece.

• Although this saw will cut wood and many nonferrous materials,

these operating instructions refer to the cutting of wood only. The

same guide-lines apply to the other materials. Do not cut ferrous

(iron and steel) materials, fibre cement or masonry with this saw!

• Make sure to use the kerf plate. Do not operate the machine if the

kerf slot is wider than 10 mm.

Switching On and Off (ﬁ g. M)

A hole (65) is provided in the trigger for insertion of a padlock to lock the

tool.

• To run the tool, press the on/off switch (1).

• To stop the tool, release the switch.

Setting the Variable Speed (ﬁ g. M)

DW712

The speed control dial (19) can be used for advance setting of the

required range of speed.

• Turn the dial button (19) to the desired range, which is indicated

by a number.

• Use high speeds for sawing soft materials such as wood. Use low

speeds for sawing metal.

Basic Saw Cuts

VERTICAL STRAIGHT CROSS CUT (FIG. A1, A2 & N)

• Release the mitre lever (4) and depress the mitre latch (5).

• Engage the mitre latch at the 0° position and tighten the mitre lever.

• Place the wood to be cut against the fence (3 & 7).

• Take hold of the operating handle (18) and depress the head lock

up release lever (17) to release the head. Press the trigger switch

(1) to start the motor.

• Depress the head to allow the blade to cut through the timber and

enter the plastic kerf plate (31).

DeWalt D712N Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info