Bedienungsanleitung DeWalt D821 (Seite 23 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

447222

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

18 en - 5

ENGLISH

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Mounting and removing the guard (fig. B & C)

Mounting

• Place the angle grinder on a table, spindle up.

• Align the lug (7) with the slot (8) in the bracket.

• Press the guard (3) down and turn it in the

direction of the arrow (fig. B).

The guard locking pin (9) prevents the

guard from coming loose.

Removing

• Hold the tool in your hand.

• Rotate the guard (3) in the direction of the arrow

(fig. C).

• Use a screwdriver to press the locking pin (9) in

the slot.

• Release the guard.

Mounting and removing a grinding wheel or

cutting disk (fig. D & E)

• Place the tool on a table, guard up.

• Fit the spacer (11) correctly onto the spindle (10).

• Place the grinding wheel or cutting disk on the

spacer.

• Screw the threaded flange (12) onto the spindle (10).

• Press the spindle lock (4) and rotate the grinding

wheel or cutting disk until it locks in position.

• Tighten the threaded flange using the two-pin

spanner (13) supplied.

• Release the spindle lock.

• To remove the grinding wheel or cutting disk,

loosen the threaded flange using the two-pin

spanner (while the spindle lock is engaged).

Fitting a wire cup brush

• Screw the wire cup brush directly onto the

spindle without using the spacer and threaded

flange.

Mounting and removing the rubber backing pad

(fig. F)

The rubber backing pad is available as an option.

• Remove the guard from the tool.

• Press the backing pad (15) onto the spindle (10).

The spacer is not needed.

• Position the abrasive disk (14) on the pad.

• Screw the threaded flange (12) onto the spindle (10).

• Press the spindle lock and rotate the pad until it

locks in position.

• Tighten the threaded flange using the two-pin

spanner supplied.

• Release the spindle lock.

• To remove the pad, loosen the threaded flange

using the two-pin spanner (while the spindle lock

is engaged).

Mounting the side handle (fig. H)

• Screw the side handle (2) tightly into one of the

holes (16) on either side of the gear case.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the tool.

Do not exert side pressure on the

grinding wheel or cutting disk.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

• Install the appropriate guard and disk or wheel.

Do not use excessively worn disks or wheels.

• Be sure the spacer and threaded flange are

mounted correctly.

• Make sure the disk or wheel rotates in the

direction of the arrows on the accessory and

the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D821 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info