Bedienungsanleitung DeWalt dc 234 kl (Seite 47 von 204) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388886

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

ENGLISH

Switching On and Off (ﬁ g. A)

• To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the switch.

• To lock the tool in off position, move the

forward/reverse slider (2) to the central position.

Hammerdrilling (ﬁ g. A)

• Set the mode selector switch (3) to the

"hammerdrilling" position.

• Insert the appropriate drill bit. For best results

use high quality carbide-tipped bits.

• Adjust the side handle (9) as required.

• If necessary, set the drilling depth.

• Mark the spot where the hole is to be drilled.

• Place the drill bit on the spot and switch on the

tool.

Rotary Drilling (ﬁ g. A)

• Set the mode selector switch (3) to the "rotary

drilling" position.

• Depending on your tool, follow either of the

following instructions:

- Fit a chuck adaptor/chuck assembly (DC228,

DC232). Special SDS Plus adaptors with

threaded sections are available for use with

standard 10 or 13 mm chucks to enable

straight shank bits to be used.

- Replace the tool holder with the chuck

(DC229, DC234).

• Proceed as described for hammerdrilling.

CAUTION: Never use standard chucks

in the hammerdrilling mode.

Screwdriving (ﬁ g. A)

• Set the mode selector switch (3) to the "rotary

drilling" position.

• Select the direction of rotation.

• Depending on your tool, follow either of the

following instructions:

- Insert the special SDS Plus

screwdriving

adaptor for use with hexagonal screwdriver bits

(DC228, DC232).

- Replace the tool holder with the chuck

(DC229, DC234).

• Insert the appropriate screwdriver bit. When

driving slotted head screws always use bits with

a ﬁ nder sleeve.

• Gently press the variable speed switch (1) to

prevent damage to the screw head. In reverse

(LH) rotation the tool speed is automatically

reduced for easy screw removal.

• When the screw is ﬂ ush with the workpiece,

release the variable speed switch to prevent the

screw head from penetrating into the workpiece.

DC228, DC229, DC234 - Chipping (ﬁ g. A)

• Set the mode selector switch (3) to the

"hammering only" position.

• Insert the appropriate chisel and check if it is

properly locked.

• Adjust the side handle (9) as required.

• Switch on the tool and start working.

It may be necessary to brieﬂ y run the motor after

having changed from chiselling to rotary modes in

order to align the gears.

WARNING:

• Do not use this tool to mix or pump

easily combustible or explosive ﬂ uids

(benzine, alcohol, etc.).

• Do not mix or stir inﬂ ammable liquids

labelled accordingly.

Optional Accessories

WARNING: Since accessories, other

than those offered by D

EWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only D

EWALT, recommended

accessories should be used with this

product.

Various types of SDS Plus

drill bits and chisels

are available as an option.

Consult your dealer for further information on the

appropriate accessories.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dc 234 kl Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info