Bedienungsanleitung DeWalt dc 415 kl (Seite 40 von 180) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

391299

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

ENGLISH

1. Open the guard latch (n), and align the lugs (p)

on the guard with the slots (o) on the gear case.

2. Push the guard down until the guard lugs

engage and rotate freely in the groove on the

gear case hub.

3. With the guard latch open, rotate the guard (h)

into the desired working position. The guard

body should be positioned between the spindle

and the operator to provide maximum operator

protection.

4. Close the guard latch to secure the guard on

the gear case. You should not be able to rotate

the guard by hand when the latch is closed. Do

not operate the grinder with a loose guard or

the clamp lever in open position.

5. To remove the guard, open the guard latch,

rotate the guard so that the lugs are aligned

with the slots and pull up on the guard.

NOTE: The guard is pre-adjusted to the diameter of

the gear case hub at the factory. If, after a period of

time, the guard becomes loose, tighten the adjusting

screw (q) with clamp lever in the closed position with

guard installed on the tool.

CAUTION: If the guard cannot be

tightened by the adjusting clamp, do

not use the tool. To reduce the risk of

personal injury, take the tool and guard

to a service center to repair or replace

the guard.

CAUTION: To reduce the risk of

damage to the tool, do not tighten the

adjusting screw with the clamp lever

in the open position. Undetectable

damage to the guard or the mounting

hub may result.

NOTE: Edge grinding and cutting can be performed

with Type 27 wheels designed and specified for this

purpose; 6.35 mm (1/4") thick wheels are designed

for surface grinding while 3.17 mm (1/8") wheels are

designed for edge grinding.

OPERATION

Switch

LOCK-OFF BUTTON AND TRIGGER SWITCH (FIG. 5)

Your cut-off tool is equipped with a lock-off button (b).

To lock the trigger switch, press the lock-off button

as shown. When the lock-off button is depressed to

the lock icon, the unit is locked.

Always lock the trigger switch when carrying or

storing the tool to eliminate unintentional starting.

To unlock the trigger switch, press the lock-off

button. When the lock-off button is depressed to the

unlock icon, the unit is unlocked. The lock-off button

is colored red to indicate when the switch is in its

unlocked position.

Pull the trigger switch (a) to turn the tool ON.

Releasing the trigger switch turns the tool OFF.

NOTE: This tool has no provision to lock the switch in

the ON position, and should never be locked ON by

any other means.

CAUTION: Hold the side handle and

body of the tool firmly to maintain

control of the tool at start up and during

use and until the wheel or accessory

stops rotating. Make sure the wheel has

come to a complete stop be fore laying

the tool down.

CAUTION: Allow the tool to reach full

speed before touching tool to the work

surface. Lift the tool from the work

surface before turning the tool off.

SPINDLE LOCK

The spindle lock pin is provided to prevent the

spindle from rotating when installing or removing

wheels. Operate the spindle lock pin only when the

tool is turned off, the battery is removed, and the

wheel has come to a complete stop.

CAUTION: To reduce the risk of

damage to the tool, do not engage the

spindle lock while the tool is operating.

Damage to the tool will result and

attached accessory may spin off

possibly resulting in injury.

To engage the lock, depress the spindle lock button

and rotate the spindle until you are unable to rotate

the spindle further.

Mounting and Using Depressed

Center Grinding Wheels and

Sanding Flap Discs

MOUNTING AND REMOVING HUBBED WHEELS (FIG. 6)

WARNING: To reduce the risk of

serious personal injury, turn tool off and

remove battery pack before making

any adjustments or removing/installing

attachments or accessories.

Hubbed wheels install directly on the M14 threaded

spindle.

1. Thread the wheel on the spindle by hand.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dc 415 kl Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info