Bedienungsanleitung DeWalt dc 721 kb (Seite 44 von 204) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

388423

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

ENGLISH

ASSEMBLY AND ADJUSTMENTS

WARNING: Prior to assembly and

adjustment, always remove the battery

pack. Always switch off the tool before

inserting or removing the battery pack.

WARNING: Use only DEWALT battery

packs and chargers.

Inserting and Removing the

Battery Pack from the Tool (ﬁ g. 2)

WARNING: To reduce the risk of

serious personal injury, turn tool off

and disconnect battery pack before

making any adjustments or removing/

installing attachments or accessories.

An accidental start-up can cause injury.

NOTE: Make sure your battery pack is fully charged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the base of the tool with the notch inside

the tool’s handle (fig. 2).

2. Slide the battery pack firmly into the handle until

you hear the lock snap into place.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the battery release buttons (h) and firmly

pull the battery pack out of the tool handle.

2. Insert battery pack into the charger as

described in the charger section of this manual.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Proper Hand Position (ﬁ g. 7)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the top

of the drill (k) as shown, with the other hand on the

main handle (i).

Variable Speed Switch (ﬁ g. 1)

To turn the tool on, squeeze the trigger switch (a).

To turn the tool off, release the trigger switch. Your

tool is equipped with a brake. The chuck will stop as

soon as the trigger switch is fully released.

NOTE: Continuous use in variable speed range is

not recommended. It may damage the switch and

should be avoided.

Forward/Reverse Control Button

(ﬁ g. 1)

A forward/reverse control button (b) determines the

direction of the tool and also serves as a lock off

button.

To select forward rotation, release the trigger

switch and depress the forward/reverse control

button on the right side of the tool.

To select reverse, depress the forward/reverse

control button on the left side of the tool.

The center position of the control button locks the

tool in the off position. When changing the position

of the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing

the direction of rotation, you may hear a click on

start up. This is normal and does not indicate a

problem.

Torque Adjustment Collar (ﬁ g. 1)

Your tool has an adjustable torque screwdriver

mechanism for driving and removing a wide array of

fastener shapes and sizes and in some models, a

hammer mechanism for drilling into masonry. Circling

the collar (c) are numbers, a drill bit symbol, and in

some models, a hammer symbol. These numbers

are used to set the clutch to deliver a torque range.

The higher the number on the collar, the higher the

torque and the larger the fastener which can be

driven. To select any of the numbers, rotate until the

desired number aligns with the arrow.

Dual Range Gearing (ﬁ g. 1)

The dual range feature of your driver/drill allows you

to shift gears for greater versatility.

To select the low speed, high torque setting, turn

the tool off and permit to stop. Slide the gear

selector (d) forward (towards the chuck) as shown

in Figure 1.

To select the high speed, low torque setting, turn the

tool off and permit to stop. Slide the gear selector

back (away from chuck).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dc 721 kb Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info