546198
39
Zoom out
Zoom in
Vorherige Seite
1/170
Nächste Seite
ENGLISH
35
Battery charging
Battery charged
Battery defective
Hot\cold pack delay
Do not probe with conductive objects.
Do not charge damaged battery packs
Use only with DEWALT battery packs,
others may burst, causing personal injury
and damage.
Do not expose to water.
Have defective cords replaced
immediately.
Charge only between 4 °C and 40 °C.
Discard the battery pack with due care for
the environment.
Do not incinerate the battery pack NiMH/
NiCd+.
Charges NiMH and NiCd
battery packs.
See technical data for charging time.
Charger
The DE9130 chargers accept DEWALT NiCd and
NiMH battery packs ranging from 7.2 to 18 V.
Battery pack (fi g. 1)
BATTERY TYPE
The DC352 operates on a 18 volt battery pack.
Charging the battery pack (fi g. 2)
When charging the battery pack (n) for the first time,
or after prolonged storage, it will only accept an
80% charge. After several charge and discharge
cycles, the battery pack will attain full capacity.
Always check the mains prior to charging the battery
pack. If the mains is functioning but the battery pack
does not charge, take your charger to an authorised
D
EWALT repair agent. Whilst charging, the charger
and the battery pack may become warm to touch.
This is a normal condition and does not indicate a
problem.
CAUTION: Do not charge the battery
pack at ambient temperatures < 4 °C
or > 40 °C. Recommended charging
temperature: approx. 24 °C.
To charge the battery pack (n), insert it into the
charger (o) as shown and plug in the charger. Be
sure that the battery pack is fully seated in the
charger. The red charging indicator will blink.
After approx. 1 hour, it will stop blinking and remain
on. The battery pack is now fully charged. The
battery pack can be removed at any time or left in
the connected charger for a longer period of time
(with a maximum of 14 days).
Battery cap (fi g. 3)
A protective battery cap (p) is supplied to cover the
contacts of a detached battery pack. Without the
protective cap in place, loose metal objects could
short circuit the contacts, causing a fire hazard and
damaging the battery pack.
1. Take off the protective battery cap (p) before
placing the battery pack (n) in the charger
or tool (fig. 3A).
2. Place the protective cap over the contacts
immediately after removing the battery pack
from the charger or tool (fig. 3B).
WARNING: Make sure the protective
battery cap is in place before storing or
carrying a detached battery pack.
Automatic refresh
The automatic refresh mode will equalize or balance
the individual cells in the battery pack at its peak
capacity. Battery packs should be refreshed
overnight after every 10th charge/discharge cycle
or whenever the pack no longer delivers the same
amount of work.
To refresh your battery pack, place it in the charger
as usual. The red light will blink continuously
indicating that the charge cycle has started.
When the 1-hour charge cycle has completed, the
light will stay on continuously and will no longer
blink. The battery pack is fully charged and can be
used at this time.
39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt DC351KL wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info