Bedienungsanleitung DeWalt DC720K T 10 (Seite 40 von 204) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

549321

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

ENGLISH

DATE CODE POSITION

The Date Code, which also includes the year of

manufacture, is printed into the housing surface that

forms the mounting joint between tool and battery!

Example:

2010 XX XX

Year of Manufacture

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual

contains important safety and operating instruc-

tions for the DE9130, DE9135 and DE9116 battery

chargers.

• Before using charger, read all instructions and

cautionary markings on charger, battery pack,

and product using battery pack.

DANGER: Electrocution hazard. 230

volts are present at charging terminals.

Do not probe with conductive objects.

Electric shock or electrocution may

result.

WARNING: Shock hazard. Do not allow

any liquid to get inside charger. Electric

shock may result.

CAUTION: Burn hazard. To reduce

the risk of injury, charge only DEWALT

rechargeable batteries. Other types of

batteries may burst causing personal

injury and damage.

CAUTION: Under certain conditions,

with the charger plugged in to the

power supply, the exposed charging

contacts inside the charger can be

shorted by foreign material. Foreign

materials of a conductive nature such

as, but not limited to, steel wool,

aluminum foil, or any buildup of metallic

particles should be kept away from

charger cavities. Always unplug the

charger from the power supply when

there is no battery pack in the cavity.

Unplug charger before attempting to

clean.

• DO NOT attempt to charge the battery pack

with any chargers other than the ones in

this manual. The charger and battery pack are

specifically designed to work together.

• These chargers are not intended for

any uses other than charging DEWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock or

electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when

disconnecting charger. This will reduce risk of

damage to electric plug and cord.

• Make sure that cord is located so that it

will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

• Do not use an extension cord unless it

is absolutely necessary. Use of improper

extension cord could result in risk of fire, electric

shock, or electrocution.

• An extension cord must have adequate wire

size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the

wire, the greater the capacity of the cable, that

is 16 gauge has more capacity than 18 gauge.

When using more than one extension to make

up the total length, be sure each individual

extension contains at least the minimum wire

size.

• Do not place any object on top of charger

or place the charger on a soft surface that

might block the ventilation slots and result

in excessive internal heat. Place the charger

in a position away from any heat source. The

charger is ventilated through slots in the top and

the bottom of the housing.

• Do not operate charger with damaged cord

or plug — have them replaced immediately.

• Do not operate charger if it has received a sharp

blow, been dropped, or otherwise damaged in

any way. Take it to an authorized service center.

• Do not disassemble charger; take it to an

authorized service center when service or

repair is required. Incorrect reassembly may

result in a risk of electric shock, electrocution or

fire.

• Disconnect the charger from the outlet

before attempting any cleaning. This will

reduce the risk of electric shock. Removing

the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on

standard 230V household electrical power.

Do not attempt to use it on any other

voltage. This does not apply to the vehicular

charger.

SAVE THESE INSTRUCTIONS

Chargers

The DE9130 and DE9116 charger accepts

7.2–18 V NiCd and NiMH batteries.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC720K T 10 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DC720K T 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info