Bedienungsanleitung DeWalt DC720K T 10 (Seite 11 von 20) (Englisch)

549321

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

• The charger is designed to operate on

standard 230V household electrical power.

Do not attempt to use it on any other

voltage. This does not apply to the vehicular

charger.

SAVE THESE INSTRUCTIONS

Chargers

The DE9130 and DE9116 charger accepts

7.2–18 V NiCd and NiMH batteries.

The DE9135 charger accepts 7.2–18 V NiCd, NiMH

or Li-Ion batteries.

These chargers require no adjustment and are

designed to be as easy as possible to operate.

Charging Procedure (ﬁ g. 2)

DANGER: Electrocution hazard.

230 volts present at charging terminals.

Do not probe with conductive objects.

Danger of electric shock or

electrocution.

1. Plug the charger (j) into an appropriate outlet

before inserting battery pack.

2. Insert the battery pack (g) into the charger.

The red (charging) light will blink continuously

indicating that the charging process has started.

3. The completion of charge will be indicated by

the red light remaining ON continuously. The

pack is fully charged and may be used at this

time or left in the charger.

NOTE: To ensure maximum performance and life of

NiCd, NiMH and Li-Ion batteries, charge the battery

for a minimum of 10 hours before first use.

Charging Process

Refer the table below for the state of charge of the

battery pack.

State of charge

charging – – – – – –

fully charged –––––––––––

hot/cold pack delay ––– – ––– –

replace battery pack •••••••••••

problem •• •• •• ••

Automatic Refresh

The automatic refresh mode will equalise or balance

the individual cells in the battery pack at its peak

capacity. Battery packs should be refreshed weekly

or whenever the pack no longer delivers the same

amount of work.

To refresh your battery pack, place the battery in the

charger as usual. Leave the battery pack for at least

10 hours in the charger.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot

or too cold, it automatically starts a Hot/Cold Pack

Delay, suspending charging until the battery has

reached an appropriate temperature. The charger

then automatically switches to the pack charging

mode. This feature ensures maximum battery life.

LI-ION BATTERY PACKS ONLY

Li-Ion batteries are designed with an Electronic

Protection System that will protect the battery

against overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the

Li-Ion battery on the charger until it is fully charged.

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure

to include catalog number and voltage. Consult the

chart at the end for compatibility of chargers and

battery packs.

The battery pack is not fully charged out of the

carton. Before using the battery pack and charger,

read the safety instructions below. Then follow

charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Inserting

or removing the battery from the charger may

ignite the dust or fumes.

• Charge the battery packs only in DEWALT

chargers.

• DO NOT splash or immerse in water or other

liquids.

• Do not store or use the tool and battery

pack in locations where the temperature

may reach or exceed 40˚ C (105° F) (such as

outside sheds or metal buildings in summer).

DANGER: Never attempt to open the

battery pack for any reason. If battery

pack case is cracked or damaged,

do not insert into charger. Do not

crush, drop or damage battery pack.

Do not use a battery pack or charger

that has received a sharp blow, been

dropped, run over or damaged in any

way (i.e., pierced with a nail, hit with a

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC720K T 10 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DC720K T 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info