Bedienungsanleitung DeWalt DC740 T 4 (Seite 41 von 176) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549070

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

ENGLISH

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on top of

the housing, with the other hand on the grip (h).

SWITCHING ON AND OFF (FIG. 1, 6)

1. To run the tool, press the variable speed switch

(a). The pressure exerted on the variable speed

switch determines the tool speed.

2. To stop the tool, release the switch.

3. To lock the tool in the off position, move the

forward/reverse slider (b) to the central position.

WARNING: To reduce the risk of

personal injury the drill is equipped with

a brake to stop the tool as soon as the

variable speed switch is fully released.

Drill Operation

1. Select the desired speed/torque range using the

gear shifter to match the speed and torque to

the planned operation.

2. For WOOD, use twist bits, spade bits, power

auger bits or hole saws. For METAL, use high-

speed steel twist drill bits or hole saws. Use

a cutting lubricant when drilling metals. The

exceptions are cast iron and brass which should

be drilled dry.

3. Always apply pressure in a straight line with the

bit. Use enough pressure to keep the drill bit

biting, but do not push hard enough to stall the

motor or deflect the bit.

4. Hold tool firmly with both hands to control the

twisting action of the drill.

5. IF DRILL STALLS, it is usually because it

is being overloaded. RELEASE TRIGGER

IMMEDIATELY, remove drill bit from work, and

determine cause of stalling. DO NOT CLICK

TRIGGER OFF AND ON IN AN ATTEMPT

TO START A STALLED DRILL – THIS CAN

DAMAGE THE DRILL.

6. Keep the motor running when pulling the bit

back out of a drilled hole. This will help prevent

jamming.

SCREWDRIVING (FIG. 1)

1. Select forward or reverse rotation using the

slider(b). Match the speed and torque to the

planned operation. Insert the desired fastener

accessory into the chuck as you would any drill

bit.

2. Set the collar (d) to position 1 and begin

screwdriving (low torque). Make a few practice

runs in scrap or unseen areas to determine the

proper position of the clutch collar.

3. If the clutch ratchets too soon, adjust the collar

to increase the torque as required.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

serious personal injury, turn tool off

and disconnect battery pack before

making any adjustments or removing/

installing attachments or accessories.

An accidental start-up can cause injury.

The charger is not serviceable. There are no

serviceable parts inside the charger.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect

the charger from the AC outlet before

cleaning. Dirt and grease may be

removed from the exterior of the charger

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC740 T 4 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DC740 T 4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info