Bedienungsanleitung DeWalt DC740 T 4 (Seite 14 von 20) (Englisch)

549070

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the base of the tool with the notch inside

the tool’s handle (fig. 2).

2. Slide the battery pack firmly into the handle until

you hear the lock snap into place.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the release buttons (j) and firmly pull the

battery pack out of the tool handle.

2. Insert battery pack into the charger as

described in the charger section of this manual.

INSERTING AND REMOVING BITS (FIG. 1, 4)

1. Open the chuck by turning the sleeve (p)

counterclockwise and insert the bit shank.

2. Place the bit in the chuck as far as it will go and

lift slightly before tightening.

3. Tighten firmly by turning the sleeve clockwise.

4. To remove the bit, proceed in reverse order.

SELECTING THE OPERATING MODE OR ADJUSTING THE

TORQUE (FIG. 5)

The collar of this tool has 15 positions for the

adjustment of the torque to suit the size of the screw

and the workpiece material. For torque adjustment,

refer to Screwdriving.

Select the drilling mode or torque by aligning the

symbol or number on the collar (e) with the indicator

(q) on the housing.

FORWARD/REVERSE SLIDER (FIG. 6)

To select forward or reverse rotation, use the

forward/ reverse slider (b) as shown (see arrows on

tool).

WARNING: To reduce the risk of

personal injury, always wait until the

motor has come to a complete standstill

before changing the direction of rotation.

TWO-GEAR SELECTOR (FIG. 7)

Your tool is fitted with a two-gear selector (f) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes, driving screws)

2 high speed/low torque

(drilling smaller holes)

For speed rates, refer to the Technical Data.

WARNING: To reduce the risk of

personal injury:

• Always push the two gear selector

completely forward or backward.

• Do not change gears at full speed or

during use.

Removing and Fitting the Chuck

(ﬁ g. 8, 9)

DW907

1. Open the chuck jaws as far as possible.

2. Insert a screwdriver into the chuck and remove

the chuck retaining screw by turning clockwise

as shown in figure 8.

3. Tighten an hex key into the chuck and strike it

with a hammer as shown in figure 9. This will

loosen the chuck so that it can be unscrewed

by hand.

4. To refit the chuck, proceed in reverse order.

Prior to Operation

1. Make sure your battery pack is (fully) charged.

2. Insert the appropriate bit.

3. Mark the spot where the hole is to be drilled.

4. Select forward or reverse rotation.

OPERATION

Instructions for Use

WARNING: To reduce the risk of

personal injury:

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to

the tool. Excessive force does not

speed up drilling but decreases tool

performance and may shorten tool life.

• To minimise stalling on break-through,

progressively reduce the drill point

pressure towards the end of the

operation.

• Keep the motor running when pulling

the bit back out of a drilled hole. This

will help prevent jamming.

Proper Hand Position (ﬁ g. 1, 10)

WARNING: To reduce the risk of

serious personal injury, ALWAYS

use proper hand position as shown

in figure 10.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC740 T 4 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DC740 T 4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info