Bedienungsanleitung DeWalt DC757K T 10 (Seite 26 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

549074

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH

• Take off the protective cap (13) before placing

the battery pack (9) in the charger or tool.

• Place the protective cap over the contacts

immediately after removing the battery pack from

the charger or tool.

Make sure the protective cap is in place

before storing or carrying a detached

battery pack.

Equalisation mode

The equalisation mode helps to maintain the

optimum capacity of the battery pack. It is therefore

recommended to use the equalisation mode weekly

or every 10 charge/discharge cycles.

• Charge the battery pack as described above.

• When the charging indicator stops blinking, leave

the battery in the charger for approx. 4 hours.

DE9116 - Hot Pack Delay

When the charger detects a battery that is hot,

it automatically starts a Hot Pack Delay, suspending

charging until the battery has cooled. After the

battery has cooled, the charger automatically

switches to the pack charging mode. This feature

ensures maximum battery life. The red indicator (12)

blinks long, then short while in the Hot Pack Delay

mode.

Inserting and removing bits (fig. A & C)

• Open the chuck by turning the sleeve (14)

counterclockwise and insert the bit shank.

• Place the bit in the chuck as far as it will go and

lift slightly before tightening.

• Tighten firmly by turning the sleeve clockwise.

• To remove the bit, proceed in reverse order.

Selecting the operating mode or adjusting the

torque (fig. D)

The collar of this tool has 17 positions for the

adjustment of the torque to suit the size of the screw

and the workpiece material. For torque adjustment,

refer to the section «Screwdriving».

• Select the drilling mode or torque by aligning the

symbol or number on the collar (4) with the

indicator (15) on the housing.

Forward/reverse slider (fig. E)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Two gear selector (fig. F)

Your tool is fitted with a two gear selector (3) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes, driving screws)

2 high speed/low torque

(drilling smaller holes)

For speed rates, refer to the technical data.

Always push the two gear selector

completely forward or backward.

• Do not change gears at full speed or during use.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Switching on and off (fig. A & E)

• To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the switch.

• To lock the tool in the off position, move the

forward/reverse slider (2) to the central position.

The drill is equipped with a brake to stop

the tool as soon as the variable speed

switch is fully released.

Screwdriving (fig. A)

• Select forward or reverse rotation using the slider

(2).

• Set the collar (4) to position 1 and begin

screwdriving (low torque).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC757K T 10 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DC757K T 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info