Bedienungsanleitung DeWalt DC810 T 1 (Seite 35 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

550288

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

ENGLISH

WARNING: Use only DEWALT battery

packs and chargers.

Fitting and removing the battery pack (fig. A)

• To fit the battery pack (5), line it up with the

receptacle on the tool. Slide the battery pack into

the receptacle and push until the battery snaps

into place.

• To remove the battery pack, push the release

button (6) while at the same time pulling the

battery pack out of the receptacle.

Fitting and removing sockets (ﬁ g. C)

The tool uses a 1/2" square drive system with detent

pin.

Fitting sockets

• Align the hole (9) in the side of the socket with

the detent pin (10) on the anvil.

• Push the socket (11) onto the anvil (2) until it

snaps into place. Tap it lightly if required.

Removing sockets

• Depress the detent pin (10) through the hole (9) in

the socket and pull the socket off the anvil.

Prior to operation:

• Make sure your battery pack is (fully) charged.

• Make sure the battery pack is properly seated.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Proper Hand Position (ﬁ g. D)

WARNING: To reduce the risk of serious

personal injury, ALWAYS use proper

hand position as shown.

WARNING: To reduce the risk of serious

personal injury, ALWAYS hold securely in

anticipation of a sudden reaction.

Proper hand position requires one hand on the pistol

grip (3) as shown.

Switching on and off

DC800 (ﬁ g. A)

• To run the tool, press the on/off switch (1).

- To select forward rotation, press the lower part

of the switch.

- To select reverse rotation, press the upper part

of the switch.

• To stop the tool, release the switch.

DC810 (ﬁ g. A)

Variable Speed switch

• To run the tool, press the on/off switch (1).

• To stop the tool, release the switch.

Your tool is equipped with a brake. The anvil will

stop as soon as the trigger switch is fully released.

The variable speed switch enables you to select the

best speed for a particular application.

The more you squeeze the trigger, the faster the tool

will operate. Use lower speeds for starting screws or

fasteners. For maximum tool life, use variable speed

only for starting fasteners.

NOTE: Continuous use in variable speed range is

not recommended. It may damage the switch and

should be avoided.

WARNING: Always wait until the motor

has come to a complete standstill before

changing the direction of rotation.

Forward/Reverse button – DC810

A forward/reverse button (4) determines the direction

of the tool and also serves as a lock off button.

To select forward rotation, release the trigger switch

and depress the forward/reverse control button on

the right side of the tool.

To select reverse, depress the forward/reverse

control button on the left side of the tool.

The center position of the control button locks the

tool in the off position. When changing the position

of the control button, be sure the trigger is released.

NOTE: The ﬁ rst time the tool is run after changing

the direction of rotation, you may hear a click on

start up. This is normal and does not indicate a

problem.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC810 T 1 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info