Bedienungsanleitung DeWalt DC901 T 1 (Seite 37 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549646

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

ENGLISH

WARNING: Always wait until the motor

has come to a complete standstill before

changing the direction of rotation.

Three-gear Selector (ﬁ g. F)

Your tool is ﬁ tted with a three-gear selector (6) to

vary the speed/torque ratio.

1 low speed/high torque

2 medium speed/medium torque

3 high speed/low torque

For speed rates, refer to the technical data.

• Do not change gears at full speed or during use.

Prior to Operation

• Make sure your battery pack is (fully) charged.

• Make sure the battery pack is properly seated.

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

OPERATION

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Instructions for Use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

Proper Hand Position (ﬁ g. A, G)

WARNING: To reduce the risk of serious

personal injury, ALWAYS use proper

hand position as shown.

WARNING: To reduce the risk of serious

personal injury, ALWAYS hold securely in

anticipation of a sudden reaction.

Proper hand position requires one hand on the side

handle (9), with the other hand on the grip (8).

Switching On and Off (ﬁ g. A & E)

• To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the switch.

• To lock the tool in the off position, move the

forward/reverse slider (2) to the central position.

Screwdriving (ﬁ g. A)

• Select the drilling mode using the collar (5).

• Select forward or reverse rotation using the

slider (2).

• Set the collar (4) to position 1 and begin

screwdriving (low torque).

• If the clutch ratchets too soon, adjust the collar

to increase the torque as required.

Drilling (ﬁ g. A)

• Select the drilling mode using the collar (5).

• Select forward rotation using the slider (2).

Drilling in Metal

• Use a cutting lubricant when drilling metals.

The exceptions are cast iron and brass which

should be drilled dry.

Drilling in Wood

• Use the appropriate type of drill bit.

Consult your dealer for further information on the

appropriate accessories.

MAINTENANCE

Your D E WALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up can

cause injury.

Lubrication

Your power tool requires no additional lubrication.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC901 T 1 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DC901 T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info