Bedienungsanleitung DeWalt DC925K T 11 (Seite 15 von 20) (Englisch)

549621

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

NOTE: The first time the tool is run after changing

the direction of rotation, you may hear a click on

start up. This is normal and does not indicate a

problem.

Worklight (ﬁ g. 1)

There is a worklight (c) located just above the trigger

switch (a). The worklight will be activated when the

trigger switch is squeezed.

NOTE: The worklight is for lighting the immediate

work surface and is not intended to be used as a

flashlight.

Mode Control Collar (ﬁ g. 4–6)

Your drill is equipped with a separate mode control

collar (f) to switch between drilling, screwdriving and

hammerdrilling mode.

DRILLING (FIG. 4)

CAUTION: When the mode collar is in

the drill/hammerdrill mode, the drill will

not clutch out regardless of the position

of the torque adjustment collar (e).

Rotate the mode control collar (f) so the drill symbol

is aligned with the arrow.

NOTE: The torque adjustment collar (e) may be set

on any number.

SCREWDRIVING (FIG. 5)

Rotate the mode control collar (f) so the screw

symbol is aligned with the arrow.

NOTE: The torque adjustment collar may be

set to any number at any time. However, the

torque adjustment collar is only engaged during

screwdriving mode and not in drill and hammerdrill

modes.

HAMMERDRILLING (FIG. 6)

CAUTION: When the mode collar is in

the drill/hammerdrill mode, the drill will

not clutch out regardless of the position

of the torque adjustment collar (e).

Rotate the mode control collar (f) so the hammer

symbol is aligned with the arrow.

Torque Adjustment Collar (ﬁ g. 4–6)

Your tool has an adjustable torque screwdriver

mechanism for driving and removing a wide array

of fastener shapes and sizes. Circling the torque

adjustment collar (e) are numbers. These numbers

are used to set the clutch to deliver a torque range.

The higher the number on the collar, the higher the

torque and the larger the fastener which can be

driven. To select any of the numbers, rotate until the

desired number aligns with the arrow.

Three-Speed Gearing (ﬁ g. 4–5)

The three-speed feature of your tool allows you to

shift gears for greater versatility. To select speed 1

(highest torque setting), turn the tool off and permit it

to stop. Slide the gear shifter (g) all the way forward.

Speed 2 (middle torque and speed setting) is in the

middle position. Speed 3 (highest speed setting) is

to the rear.

NOTE: Do not change gears when the tool is

running. Always allow the drill to come to a complete

stop before changing gears. If you have trouble

changing gears, make sure that the gear shifter is

engaged in one of the three speed settings.

Keyless Single Sleeve Chuck

(ﬁ g. 7–9)

WARNING: Do not attempt to tighten

drill bits (or any other accessory) by

gripping the front part of the chuck

and turning the tool on. Damage to

the chuck and personal injury may

result. Always lock off trigger switch

and disconnect tool from power source

when changing acces sories.

WARNING: Always ensure the bit is

secure before starting the tool. A loose

bit may eject from tool causing possible

personal injury.

Your tool features a keyless chuck with one rotating

sleeve for one-handed operation of the chuck. To

insert a drill bit or other accessory, follow these steps.

1. Lock the trigger in the OFF position. Turn off

tool and disconnect tool from power source.

2. Grasp the sleeve of the chuck (d) with one

hand and use the other hand to secure the

tool as shown in Figure 7. Rotate the sleeve

counterclockwise (as viewed from the front) far

enough to accept the desired accessory.

3. Insert the accessory about 3/4" (19 mm) into

the chuck and tighten securely by rotating the

chuck sleeve clockwise with one hand while

holding the tool with the other hand. Continue

to rotate the chuck sleeve until several ratchet

clicks are heard to ensure full gripping power.

To release the accessory, repeat Steps 1 and 2

above.

Be sure to tighten chuck with one hand on the

chuck sleeve and one hand holding the tool for

maximum tightness.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC925K T 11 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DC925K T 11

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info