Bedienungsanleitung DeWalt DC945K T 10 (Seite 12 von 16) (Englisch)

549077

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ENGLISH

● If the pack is left in the charger after the initial

charge, the charger will automatically initiate

the refresh mode. This mode will continue up to

8 hours, but the battery pack can be removed at

any time during the refresh mode.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot

or too cold, it automatically starts a Hot/Cold Pack

Delay, suspending charging until the battery has

reached an appropriate temperature. The charger

then automatically switches to the pack charging

mode. This feature ensures maximum battery life.

The red indicator (13) blinks long, then short while

in the Hot/Cold Pack Delay mode.

Inserting and removing bits (ﬁ g. A & C)

● Open the chuck by turning the sleeve (15)

counterclockwise and insert the bit shank.

● Place the bit in the chuck as far as it will go and

lift slightly before tightening.

● Tighten ﬁ rmly by turning the sleeve clockwise.

● To remove the bit, proceed in reverse order.

Selecting the operating mode or adjusting the

torque (ﬁ g. D)

The collar of this tool has a wide range of positions

for the adjustment of the torque to suit the size of

the screw and the workpiece material. For torque

adjustment, refer to the section "Screwdriving".

● Select the drilling mode or torque by aligning

the symbol or number on the collar (4) with the

indicator (16) on the housing.

DC945/DC935/DC925

These tools can be used in the following operating

modes:

Rotary drilling: for steel, wood and

plastics

Percussion drilling: for masonry

Forward/reverse slider (ﬁ g. E)

● To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always wait until the motor has come to

a complete standstill before changing

the direction of rotation.

Three-gear selector (ﬁ g. F)

Your tool is ﬁ tted with a three-gear selector (6) to

vary the speed/torque ratio.

1 low speed/high torque

2 medium speed/medium torque

3 high speed/low torque

For speed rates, refer to the technical data.

Do not change gears at full speed or

during use.

Instructions for use

● Always observe the safety instructions

and applicable regulations.

● Be aware of the location of pipework

and wiring.

● Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

Prior to operation:

● Make sure your battery pack is (fully) charged.

● Make sure the battery pack is properly seated.

● Insert the appropriate bit.

● Mark the spot where the hole is to be drilled.

Switching on and off (ﬁ g. A & E)

● To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

● To stop the tool, release the switch.

● To lock the tool in the off position, move the

forward/reverse slider (2) to the central position.

Screwdriving (ﬁ g. A)

● Select forward or reverse rotation using the

slider (2).

● Set the collar (4) to position 1 and begin

screwdriving (low torque).

● If the clutch ratchets too soon, adjust the collar

to increase the torque as required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC945K T 10 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DC945K T 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info