Bedienungsanleitung DeWalt DCD710 s2-XE (Seite 10 von 16) (Englisch)

627544

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

To select reverse, depress the forward/reverse control button on the left side of the

tool. The center position of the control button locks the tool in the off position. When

changing the position of the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing the direction of rotation, you may

hear a click on start up. This is normal and does not indicate a problem.

Worklights (Fig. 2)

There is one worklight (C) located around the chuck collar (D). The worklight will

activate when the trigger switch is pulled.

NOTE: The worklights are for lighting the immediate work surface and are not

intended to be used as a flashlight.

Torque Adjustment Collar (Fig. 2, 4)

The torque adjustment collar (D) is clearly marked with

FIG. 4

numbers and a drill bit symbol. The collar should be rotated

until the desired setting is located at the top of the tool

(Fig. 2). Locators are provided in the collar to eliminate the

guess work when selecting fastening torque. The higher the

number on the collar, the higher the torque and the larger the

fastener which can be driven. To lock the clutch for drilling

operations, move to the drill bit position.

NOTE: When using the drill/driver for drilling holes, be sure

that the torque adjusting collar is set so the figure of the drill is

aligned with the center line on the top of the tool. Failure to do

this will allow the clutch to slip while attempting to drill.

Dual Range Gearing (Fig. 2, 4)

The dual range feature of your driver/drill allows you to shift gears for greater versatility.

To select the low speed, high torque setting, turn the tool off and permit to stop. Slide

the gear shifter (E) forward (towards the chuck). To select the high speed, low torque

setting, turn the tool off and permit to stop. Slide the gear shifter back (away from

chuck).

NOTE: Do not change gears when the tool is running. If you are having trouble changing

gears, make sure that the dual range gear shifter is either completely pushed forward or

completely pushed back.

OPERATION

WARNING: To reduce the risk of serious personal injury, place the forward/

reverse button in the lock-off position or turn tool off and disconnect battery pack

before making any adjustments or removing/installing attachments or accessories.

Installing and Removing the Battery Pack (Fig. 3)

NOTE: Make sure your battery pack is fully charged.

To install the battery pack (H) into the tool handle, align the battery with the rails

inside the tool’s handle and slide it firmly into the handle until you hear the lock snap

into place.

FIG. 3

To remove the battery pack from the tool, press the release button (G) and firmly pull

the battery pack out of the tool handle. Insert it into the charger as described in the

charger section of this manual.

Variable Speed Trigger Switch (Fig. 2)

To turn the tool on, squeeze the trigger switch (A). To turn the tool off, release the

trigger switch. Your tool is equipped with a brake. The chuck will stop when the trigger

switch is fully released. The variable speed switch enables you to select the best

speed for a particular application. The more you squeeze the trigger, the faster the

tool will operate. For maximum tool life, use variable speed only for starting holes or

fasteners.

NOTE: Continuous use in variable speed range is not recommended. It may damage

the switch and should be avoided.

Forward/Reverse Control Button (Fig. 2)

A forward/reverse control button (B) determines the direction of the tool and also

serves as a lock off button.

To select forward rotation, release the trigger switch and depress the forward/reverse

control button on the right side of the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCD710 s2-XE Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info