Bedienungsanleitung DeWalt DCD710 T 1 (Seite 14 von 40) (Englisch, Französisch)

549026

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

1. Lock the trigger in the off position as previously

described.

2. Grasp the black sleeve of the chuck with one

hand and use the other hand to secure the tool.

Rotate the sleeve counterclockwise far enough to

accept the desired accessory.

3. Insert the accessory about 19 mm (3/4") into the

chuck and tighten securely by rotating the chuck

sleeve clockwise with one hand while holding the

tool with the other. Your tool is equipped with an

automatic spindle lock mechanism. This allows

you to open and close the chuck with one hand.

To release the accessory, repeat step 2 above.

WARNING:

Do not attempt to tighten drill

bits (or any other accessory) by gripping the

front part of the chuck and turning the tool

on. Damage to the chuck and personal

injury may result. Always lock off trigger

switch when changing acces sories.

Be sure to tighten chuck with one hand on the

chucksleeve and one hand holding the tool for

maximum tightness.

CHUCK REMOVAL (ﬁg. 6)

Turn the adjustment collar to the “drill” position and

gear shifter to position 1 (low speed). Tighten the

chuck around the shorter end of a hex key (not

supplied) of 6.35 mm (1/4") or greater size. Using a

wooden mallet or similar object, strike the longer end

in the clockwise direction, as shown. This will loosen

the screw inside the chuck.

Open chuck jaws fully, insert screwdriver (or Torx tool

if required) into front of chuck between jaws to

engage screw head. Remove screw by turning

clockwise (left-hand-thread). Place hex key in chuck

and tighten, as shown in Figure 6. Using a wooden

mallet or similar object, strike key sharply in the

counterclockwise direction. This will loosen the chuck

so that it can be unscrewed by hand.

CHUCK INSTALLATION (ﬁg. 7)

Screw the chuck on by hand as far as it will go and

insert screw (left-hand thread). Tighten screw

securely. Tighten the chuck around the shorter end of

a 6.35 mm (1/4") or larger hex key (not supplied)

strike the longer end in the clockwise direction with a

wooden mallet, as shown. Tighten the screw once

again by turning in a counterclockwise direction.

Drill Operation

WARNING:

To reduce the risk of serious

personal injury, turn tool off and disconnect

tool from power source before making any

adjustments or removing/installing

attachments or accessories.

WARNING: To reduce the risk of

personal injury, ALWAYS ensure

workpiece is anchored or clamped ﬁrmly. If

drilling thin material, use a wood “back-up”

block to prevent damage to the material.

Turn the collar to the drill bit symbol for drilling. Select

the desired speed/torque range using the gear shifter

to match the speed and torque to the

plannedoperation.

1. Use sharp drill bits only. For wood, use twist drill

bits, spade bits, or hole saws. For metal, use

high-speed steel (HHS) twist drill bits or hole

saws.

2. Always apply pressure in a straight line with the

bit. Use enough pressure to keep drill biting, but

do not push hard enough to stall the motor or

deﬂect the bit.

3. Hold tool ﬁrmly with both hands to control the

twisting action of the drill.

WARNING:

The drill may stall if overloaded

causing a sudden twist. Always expect the

stall. Grip the drill ﬁrmly with both hands to

control the twisting action and avoid injury.

IF DRILL STALLS, it is usually because it is being

overloaded or improperly used. RELEASE TRIGGER

IMMEDIATELY, remove drill bit from work, and

determine cause of stalling. DO NOT CLICK

TRIGGER ON AND OFF IN AN ATTEMPT TO START A

STALLED DRILL — THIS CAN DAMAGE THE DRILL.

To minimize stalling or breaking through the

material, reduce pressure on drill and ease the bit

through the last fractional part of the hole.

Keep the motor running when pulling the bit back

out of a drilled hole. This will help prevent

jamming.

With variable speed drills there is no need to

center punch the point to be drilled. Use a slow

speed to start the hole and accelerate by

squeezing the trigger harder when the hole is

deep enough to drill without the bit skipping out.

Operation as a Screwdriver

Select the desired speed/torque range using the dual

range gear shifter on the top of tool to match the

speed and torque to the planned operation.

Insert the desired fastener accessory into the chuck

as you would any drill bit. Make a few practice runs in

scrap or unseen areas to determine the proper

position of the clutch collar.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCD710 T 1 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DCD710 T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info