Bedienungsanleitung DeWalt DCD734 (Seite 35 von 148) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

739486

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

ENGLISH

Dual Range Gearing (Fig. A)

The dual range feature of your drill/driver/hammerdrill allows

you to shift gears for greaterversatility.

1. To select speed 1 (high torque setting), turn the tool off and

permit it to stop. Slide the gear shifter

4

forward (towards

the chuck).

2. To select speed 2 (low torque setting), turn the tool off and

permit it to stop. Slide the gear shifter back (away from

thechuck).

NOTE: Do not change gears when the tool is running. Always

allow the drill to come to a complete stop before changing

gears. If you are having trouble changing gears, make sure that

the dual range gear shifter is either completely pushed forward

or completely pushedback.

Worklight (Fig. A)

There is a worklight

5

located just above the trigger switch

1

The worklight is activated when the trigger switch is depressed.

When the trigger is released, the worklight will stay illuminated

for up to 20seconds.

NOTE: The worklight is for lighting the immediate work surface

and is not intended to be used as aflashlight.

Keyless Single Sleeve Chuck (Fig. G–I)



WARNING: Do not attempt to tighten drill bits (or

any other accessory) by gripping the front part of the

chuck and turning the tool on. Damage to the chuck

and personal injury may result. Always lock off trigger

switch and disconnect tool from power source when

changingacces sories.



WARNING: Always ensure the bit is secure before starting

the tool. A loose bit may eject from tool causing possible

personalinjury.

Your tool features a keyless chuck

6

with one rotating sleeve for

one-handed operation of the chuck. To insert a drill bit or other

accessory, follow thesesteps.

1. Turn tool off and disconnect tool from powersource.

2. Grasp the black sleeve of the chuck with one hand

and use the other hand to secure the tool. Rotate the

sleeve counterclockwise far enough to accept the

desiredaccessory.

3. Insert the accessory about 19 mm into the chuck and

tighten securely by rotating the chuck sleeve clockwise with

one hand while holding the tool with the other. Your tool is

equipped with an automatic spindle lock mechanism. This

allows you to open and close the chuck with onehand.

Be sure to tighten chuck with one hand on the chuck sleeve and

one hand holding the tool for maximumtightness.

To release the accessory, repeat steps 1 and 2above.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig. C)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the top of the drill as

shown, with the other hand on the main handle

9

Screwdriver Operation (Fig. D)

1. Select the desired speed/torque range using the dual

range gear selector to match the speed and torque of the

plannedoperation.

2. Turn the torque adjustment collar

3

to the desired position.

Lower numbers indicate lower torque settings; higher

numbers indicate higher torquesettings.

3. Insert the desired fastener accessory into the chuck as you

would any drillbit.

4. Make some practice runs in scrap or on unseen areas to

determine the proper position of the clutchcollar.

5. Always start with lower torque settings, then advance to

higher torque settings to avoid damage to the workpiece

orfastener.

Drill Operation (Fig. E)



WARNING: To reduce the risk of serious personal injury,

turn tool off and disconnect tool from power source

before making any adjustments or removing/installing

attachments oraccessories.



WARNING: TO REDUCE THE RISK OF PERSONAL

INJURY, ALWAYS ensure workpiece is anchored or

clamped firmly. If drilling thin material, use a wood “back-

up” block to prevent damage to thematerial.

1. Turn the collar

3

to the drillsymbol.

2. Select the desired speed/torque range using the gear shifter

to match the speed and torque to the plannedoperation.

3. For WOOD, use twist bits, spade bits, power auger bits or

hole saws. For METAL, use high-speed steel twist drill bits

or hole saws. Use a cutting lubricant when drilling metals.

The exceptions are cast iron and brass which should be

drilleddry.

4. Always apply pressure in a straight line with the bit. Use

enough pressure to keep drill biting, but do not push hard

enough to stall the motor or deflect thebit.

5. Hold tool firmly with both hands to control the twisting

action of the drill. If model is not equipped with side handle,

grip drill with one hand on the handle and one hand on the

batterypack.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCD734 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info