Bedienungsanleitung DeWalt DCD771 T 1 (Seite 42 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549604

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

ENGLISH

Inserting and Removing the

Battery Pack from the Tool (fig. 2)

WARNING: Prior to assembly and

adjustment, always remove the

battery pack. Always switch off the

tool before inserting or removing

the battery pack.

NOTE: For best results, make sure your battery

pack is fully charged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the battery pack (g) with the rails inside the

tool’s handle (fig. 2).

2. Slide it into the handle until the battery pack is

firmly seated in the tool and ensure that it does

not disengage.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the battery release button (h) and firmly

pull the battery pack out of the tool handle.

2. Insert battery pack into the charger as

described in the charger section of this manual.

FUEL GAUGE BATTERY PACKS (FIG. 2)

Some D

EWALT battery packs include a fuel gauge

which consists of three green LED lights that

indicate the level of charge remaining in the battery

pack.

To actuate the fuel gauge, press and hold the fuel

gauge button (k). A combination of the three green

LED lights will illuminate designating the level of

charge left. When the level of charge in the battery

is below the usable limit, the fuel gauge will not

illuminate and the battery will need to be recharged.

NOTE: The fuel gauge is only an indication of the

charge left on the battery pack. It does not indicate

tool functionality and is subject to variation based

on product components, temperature and end-user

application.

Variable Speed Trigger Switch

(fig.1)

To turn the tool on, squeeze the trigger switch (a).

To turn the tool off, release the trigger switch. Your

tool is equipped with a brake. The chuck will stop as

soon as the trigger switch is fully released.

NOTE: Continuous use in variable speed range is

not recommended. It may damage the switch and

should be avoided.

Forward/Reverse Control Button

(fig. 1)

A forward/reverse control button (b) determines the

direction of the tool and also serves as a lock-off

button.

To select forward rotation, release the trigger switch

and depress the forward/reverse control button on

the right side of the tool.

To select reverse, depress the forward/reverse

control button on the left side of the tool.

The center position of the control button locks

the tool in the off position. When changing the

position of the control button, be sure the trigger is

released.

NOTE: The first time the tool is run after changing

the direction of rotation, you may hear a click on

start up. This is normal and does not indicate a

problem.

Torque Adjustment Collar (fig. 1)

Your tool has an adjustable torque screwdriver

mechanism for driving and removing a wide array of

fastener shapes and sizes and in some models, a

hammer mechanism for drilling into masonry. Circling

the collar (c) are numbers, a drill bit symbol, and on

some models, a hammer symbol. These numbers

are used to set the clutch to deliver a torque range.

The higher the number on the collar, the higher the

torque and the larger the fastener which can be

driven. To select any of the numbers, rotate until the

desired number aligns with the arrow.

Dual Range Gearing (fig. 1)

The dual range feature of your drill/driver/hammerdrill

allows you to shift gears for greater versatility.

1. To select speed 1 (high torque setting), turn

the tool off and permit it to stop. Slide the gear

shifter (d) forward (towards the chuck).

2. To select speed 2 (low torque setting), turn the

tool off and permit it to stop. Slide the gear

shifter back (away from the chuck).

NOTE: Do not change gears when the tool is

running. Always allow the drill to come to a complete

stop before changing gears. If you are having trouble

changing gears, make sure that the dual range

gear shifter is either completely pushed forward or

completely pushed back.

Worklight (fig. 1)

There is a worklight (e) located just above the

trigger switch (a). The worklight is activated when

the trigger switch is depressed. When the trigger is

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCD771 T 1 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info