Bedienungsanleitung DeWalt DCD791 (Seite 36 von 152) (Alle Sprachen)

669510

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

ENGLISH



CAUTION: When using the tool as a spotlight, be sure

it is secured on a stable surface where it will not cause a

tripping or fallinghazard.



CAUTION: Remove all accessories from the chuck before

using the drill as a spotlight. Personal injury or property

damage couldresult.

Low Battery Warning

When in spotlight mode and the battery is nearing complete

discharge, the spotlight will flash twice and then dim. After two

minutes, the battery will be completely discharged and the

drill will immediately shut down. At this point, replace with a

chargedbattery.



WARNING: To reduce the risk of injury, always have a

back-up battery or secondary lighting available if the

situation warrantsit.

Keyless Single Sleeve Chuck (Fig. G–I)



WARNING: Do not attempt to tighten drill bits (or

any other accessory) by gripping the front part of the

chuck and turning the tool on. Damage to the chuck

and personal injury may result. Always lock off trigger

switch and disconnect tool from power source when

changingacces sories.



WARNING: Always ensure the bit is secure before starting

the tool. A loose bit may eject from tool causing possible

personalinjury.

Your tool features a keyless chuck

6

with one rotating sleeve for

one-handed operation of the chuck. To insert a drill bit or other

accessory, follow thesesteps.

1. Turn tool off and disconnect tool from powersource.

2. Grasp the black sleeve of the chuck with one hand

and use the other hand to secure the tool. Rotate the

sleeve counterclockwise far enough to accept the

desiredaccessory.

3. Insert the accessory about 19 mm (3/4") into the chuck and

tighten securely by rotating the chuck sleeve clockwise with

one hand while holding the tool with the other. Your tool is

equipped with an automatic spindle lock mechanism. This

allows you to open and close the chuck with onehand.

NOTE: Be sure to tighten chuck with one hand on

the chuck sleeve and one hand holding the tool for

maximumtightness.

To release the accessory, repeat steps 1 and 2above.

Belt Hook and Bit Clip (Fig. A)



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments oraccessories.



WARNING: To reduce the risk of serious personal

injury, DO NOT suspend tool overhead or suspend

objects from the belt hook. ONLY hang tool’s belt hook

from a workbelt.



WARNING: To reduce the risk of serious personal

injury, ensure the screw holding the belt hook issecure.

IMPORTANT: When attaching or replacing the belt hook or bit

clip, use only the screw

8

that is provided. Be sure to securely

tighten thescrew.

The belt hook

7

and bit clip

9

can be be attached to

either side of the tool using only the screw

8

provided, to

accommodate left- or right- handed users. If the hook or bit clip

is not desired at all, it can be removed from thetool.

To move belt hook or bit clip, remove the screw

8

that holds

it in place then reassemble on the opposite side. Be sure to

securely tighten thescrew.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig. C)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the top of the

drill

17

as shown, with the other hand on the main handle

18

Drill Operation (Fig. A, D)



WARNING: TO REDUCE THE RISK OF PERSONAL

INJURY, ALWAYS ensure workpiece is anchored or

clamped firmly. If drilling thin material, use a wood “back-

up” block to prevent damage to thematerial.

1. Turn the collar

3

to the drillsymbol.

2. Select the desired speed/torque range using the gear shifter

4

to match the speed and torque to the plannedoperation.

3. For Wood, use twist bits, spade bits, power auger bits or

hole saws. For Metal, use high-speed steel twist drill bits

or hole saws. Use a cutting lubricant when drilling metals.

The exceptions are cast iron and brass which should be

drilleddry.

4. Always apply pressure in a straight line with the bit. Use

enough pressure to keep drill biting, but do not push hard

enough to stall the motor or deflect thebit.

5. Hold tool firmly with both hands to control the twisting

action of the drill. If model is not equipped with side handle,

grip drill with one hand on the handle and one hand on the

batterypack.



CAUTION: Drill may stall if overloaded causing a sudden

twist. Always expect the stall. Grip the drill firmly to control

the twisting action and avoidinjury.

6. IF DRILL STALLS, it is usually because it is being overloaded

or improperly used. RELEASE TRIGGER IMMEDIATELY,

DeWalt DCD791 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info