Bedienungsanleitung DeWalt DCD936 T 10 (Seite 45 von 200) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549284

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

ENGLISH

To release the accessory, repeat Steps 1 and 2

above.

Be sure to tighten chuck with one hand on the

chuck sleeve and one hand holding the tool for

maximum tightness.

Belt Hook and Bit Clip (ﬁ g. 1)

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories.

WARNING: To reduce the risk of

serious personal injury, DO NOT

suspend tool overhead or suspend

objects from the belt hook. ONLY hang

tool’s belt hook from a work belt.

WARNING: To reduce the risk of

serious personal injury, ensure the

screw holding the belt hook is secure.

IMPORTANT: When attaching or replacing the

belt hook or bit clip, use only the screw (l) that is

provided. Be sure to securely tighten the screw.

The belt hook (k) and bit clip (m) can be be attached

to either side of the tool using only the screw (l)

provided, to accommodate left- or right- handed

users. If the hook or bit clip is not desired at all, it

can be removed from the tool.

To move belt hook or bit clip, remove the screw

(l) that holds it in place then reassemble on the

opposite side. Be sure to securely tighten the screw.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Proper Hand Position (ﬁ g. 9)

WARNING: To reduce the risk of

serious personal injury, ALWAYS

use proper hand position as shown

in figure 9.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the main

handle (n), with the other hand on the side handle

(h).

Drill Operation (ﬁ g. 3)

WARNING: To reduce the risk of

serious personal injury, turn tool off and

disconnect tool from power source

before making any adjustments or

removing/installing attachments or

accessories.

WARNING: To reduce the risk of

personal injury, ALWAYS ensure

workpiece is anchored or clamped

firmly. If drilling thin material, use a wood

“back-up” block to prevent damage to

the material.

1. Select the desired speed/torque range using

the gear shifter to match the speed and torque

to the planned operation. Set the mode control

collar to the drill symbol.

2. For WOOD, use twist bits, spade bits, power

auger bits or hole saws. For METAL, use high-

speed steel twist drill bits or hole saws. Use

a cutting lubricant when drilling metals. The

exceptions are cast iron and brass which should

be drilled dry.

3. Always apply pressure in a straight line with the

bit. Use enough pressure to keep the drill bit

biting, but do not push hard enough to stall the

motor or deflect the bit.

4. Hold tool firmly with both hands to control the

twisting action of the drill.

5. IF DRILL STALLS, it is usually because it

is being overloaded. RELEASE TRIGGER

IMMEDIATELY, remove drill bit from work,

and determine cause of stalling. DO NOT

CLICK TRIGGER OFF AND ON IN AN

ATTEMPT TO START A STALLED DRILL –

THIS CAN DAMAGE THE DRILL.

6. Keep the motor running when pulling the bit

back out of a drilled hole. This will help prevent

jamming.

Screwdriver Operation (ﬁ g. 4)

1. Select the desired speed/torque range using the

three-speed gear shifter (g) on the top of tool

to match the speed and torque to the planned

application. Initially set the torque adjustment

collar (e) at a lower setting to ensure the

fastener to be set to your specification.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCD936 T 10 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info