Bedienungsanleitung DeWalt DCD985 T 10 (Seite 46 von 200) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549626

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

ENGLISH

NOTE: Use the lowest torque setting required

to seat the fastener at the desired depth. The

lower the number, the lower the torque output.

2. Rotate the mode control collar (f) so the screw

symbol is aligned with the arrow.

3. Reset the torque adjustment collar (e) to the

appropriate number setting for the torque

desired. Make a few practice runs in scrap or

unseen areas to determine the proper position

of the torque adjustment collar.

NOTE: The torque adjustment collar may be

set to any number at any time. However, the

torque adjustment collar is only engaged during

screwdriving mode and not in drill and hammerdrill

modes.

Hammerdrill Operation (ﬁ g. 5)

1. Select the desired speed/torque range using

the gear shifter to match the speed and torque

to the planned operation. Set the mode control

collar (f) to the hammer symbol.

2. When drilling, use just enough force on the

hammer to keep it from bouncing excessively.

Too much force will cause slower drilling

speeds, overheating, and a lower drilling rate.

3. Drill straight, keeping the bit at a right angle to

the work. Do not exert side pressure on the bit

when drilling as this will cause clogging of the

bit flutes and a slower drilling speed.

4. When drilling deep holes, if the hammer speed

starts to drop off, pull the bit partially out of

the hole with the tool still running to help clear

debris from the hole.

5. For masonry, use carbide-tipped bits or

masonry bits. A smooth, even flow of dust

indicates the proper drilling rate.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up

can cause injury.

The charger and battery pack are not serviceable.

There are no serviceable parts inside.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect

the charger from the AC outlet before

cleaning. Dirt and grease may be

removed from the exterior of the charger

using a cloth or soft non-metallic brush.

Do not use water or any cleaning

solutions.

Optional Accessories

WARNING: Since accessories, other

than those offered by DEWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only DEWALT recommended

accessories should be used with this

product.

Consult your dealer for further information on the

appropriate accessories.

Protecting the Environment

Separate collection. This product must

not be disposed of with normal

household waste.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCD985 T 10 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DCD985 T 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info