Bedienungsanleitung DeWalt DCD995 T 1 (Seite 44 von 200) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549628

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

ENGLISH

If model is not equipped with side handle, grip drill

with one hand on the handle and one hand on the

battery pack.

NOTE: Side handle comes equipped on all models.

Forward/Reverse Control Button

(ﬁ g. 1)

A forward/reverse control button (b) determines the

direction of the tool and also serves as a lock off

button.

To select forward rotation, release the trigger switch

and depress the for ward/re verse control button on

the right side of the tool.

To select reverse, release the trigger switch and

depress the forward/reverse control button on the

left side of the tool.

The center position of the control button locks the

tool in the off position. When changing the position

of the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing

the direction of rotation, you may hear a click on

start up. This is normal and does not indicate a

problem.

Worklight (ﬁ g. 1)

There is a worklight (c) located on the foot of the

tool. The worklight is activated when the trigger

switch is depressed. When the trigger switch is

released, the worklight will stay illuminated for up to

20 seconds.

NOTE: The worklight is for lighting the immediate

work surface and is not intended to be used as a

flashlight.

Torque Adjustment Collar/Electronic

Clutch (ﬁ g. 3–5)

Your tool has an electronic adjustable torque

screwdriver mechanism for driving and removing

a wide array of fasteners. Circling the torque

adjustment collar (e) are numbers. These numbers

are used to set the clutch to deliver a torque range.

The higher the number on the collar, the higher the

torque and the larger the fastener which can be

driven. To select any of the numbers, rotate until the

desired number aligns with the arrow.

Three-Speed Gearing (ﬁ g. 1, 3–5)

The three-speed feature of your tool allows you to

shift gears for greater versatility. To select speed 1

(highest torque setting), turn the tool off and permit it

to stop. Slide the gear shifter (f) all the way forward.

Speed 2 (middle torque and speed setting) is in the

middle position. Speed 3 (highest speed setting) is

to the rear.

NOTE: Do not change gears when the tool is

running. Always allow the drill to come to a complete

stop before changing gears. If you have trouble

changing gears, make sure that the gear shifter is

engaged in one of the three speed settings.

If the speed shifter becomes stuck or is difficult to

select the desired gear, pull the trigger switch (a) to

rotate the motor. Then select the gear.

Keyless Single Sleeve Chuck

(ﬁ g. 6–8)

WARNING: Do not attempt to tighten

drill bits (or any other accessory) by

gripping the front part of the chuck

and turning the tool on. Damage to

the chuck and personal injury may

result. Always lock off trigger switch

and disconnect tool from power source

when changing acces sories.

WARNING: Always ensure the bit is

secure before starting the tool. A loose

bit may eject from tool causing possible

personal injury.

Your tool features a keyless chuck with one rotating

sleeve for one-handed operation of the chuck. To

insert a drill bit or other accessory, follow these

steps.

1. Turn off tool and disconnect tool from power

source.

2. Grasp the black sleeve of the chuck (d) with

one hand and use the other hand to secure the

tool as shown in Figure 6. Rotate the sleeve

counterclockwise (as viewed from the front) far

enough to accept the desired accessory.

3. Insert the accessory about 19 mm (3/4") into

the chuck (fig. 7). Tighten securely by rotating

the chuck sleeve clockwise with one hand while

holding the tool with the other hand (fig. 8).

Continue to rotate the chuck sleeve until several

ratchet clicks are heard to ensure full gripping

power.

To release the accessory, repeat Steps 1 and 2

above.

Be sure to tighten chuck with one hand on the

chuck sleeve and one hand holding the tool for

maximum tightness.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCD995 T 1 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DCD995 T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info