Bedienungsanleitung DeWalt DCE0811G (Seite 10 von 126) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790843

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

GB batteries; see Out of Tilt Range Indicator.) If all 4 LEDs on the

battery meter LEDs continuously ash this does not indicate

a low battery; see “The Battery Meter LEDs Flash” under

Troubleshooting.

Operation

To Turn the Lasers On and Off

(See Figure 1)

With the laser off, place it on a at level surface. Slide the

Pendulum Lock switch B to the Unlocked/ON position. The

DCE089G/R model has three ON/OFF buttons on the keypad

C one for a horizontal laser line D, one for a side vertical laser

line E and one for a front vertical laser line F (DCE089G/R

only). The DCE0811G/R has two lines -a horizontal line and

side vertical line. Each laser line is powered on by pressing its

ON/OFF button on the keypad. The laser lines can be powered

one at a time or all at the same time. Pressing the ON/OFF

keys again turns the laser lines off. Slide the Pendulum Lock

switch to the OFF/Locked position when the laser is not in use.

If the pendulum lock switch is not placed in the lock position all

4 LEDs will continuously ash on the Battery Meter.

Using the Lasers

Out of LEVEL Range Indicator

The lasers are designed to self-level. If the laser has been tilted

so much that it cannot self-level (> 4° ), the laser beam will

ash. There are two ashing sequences associated with the out

of level condition: (i) between 4° and 10° the beams ash with

a constant blink cycle; (ii) at angles greater than 10° the beams

ash with a three blink cycle. When the beams ash THE

LASER IS NOT LEVEL (OR PLUMB) AND SHOULD NOT BE

USED FOR DETERMINING OR MARKING LEVEL OR PLUMB.

Try repositioning the laser on a more level surface.

Using the Pivot Bracket (See gure 2)

WARNING:

Position the laser and/or wall mount on a stable

surface. Serious personal injury or damage to the

laser may result if the laser falls.:

The laser has a magnetic pivot bracket G permanently

attached to the unit. This bracket allows the unit to be mounted

to any upright surface made of steel or iron. Common examples

of suitable surfaces include steel framing studs, steel door

frames and structural steel beams. The bracket also has

a keyhole slot H allowing the unit to be hung from a nail or

screw on any kind of surface.

Using the Laser with the CEILING Mount

(See Figure 5 )

The laser ceiling mount L (if included) offers more mounting

options for the laser. The ceiling mount has a clamp K at

one end which can be xed to a wall angle for acoustic ceiling

installation. At each end of the ceiling mount is a screw hole M

, allowing the ceiling mount to be attached to any surface with

a nail or screw. Once the ceiling mount is secured, its steel plate

provides a surface to which the magnetic pivot bracket G can

be attached. The position of the laser can then be ne-tuned by

sliding the magnetic pivot bracket up or down on the wall mount.

Using the Lasers with Accessories

The lasers are equipped with 1/4” - 20 and 5/8” - 11

female threads on the bottom of the unit. This thread is to

accommodate current or future DeWALT accessories. Only use

DeWALT accessories specied for use with this product. Follow

the directions included with the accessory.

CAUTION:

The use of any other accessory not recommended for

use with this tool could be hazardous.

If you need any assistance in locating any accessory, please

contact your nearest DeWALT service center or go to

www.2helpU.com on the Internet.

Leveling the Lasers

As long as the laser is properly calibrated, the laser is self-

leveling. Each laser is calibrated at the factory to nd level as

long as it is positioned on a at surface within average ± 4° of

level. No manual adjustments are required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCE0811G Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info