Bedienungsanleitung DeWalt DCE0811R (Seite 9 von 126) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790844

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

To install batteries:

1. Lift up the battery compartment cover as shown in

Figure 6A .

2. Insert four fresh AA batteries in the compartment, placing

the batteries according to (+) and (–) on the inside of the

compartment.

3. Install the AA starter Battery pack as shown in Figure 6B .

Using the 10.8V Rechargeable Pack:

Install the 10.8V DeWALT Battery pack as shown in Figure 6B .

WARNING:

Batteries can explode, or leak, and can cause

injury or re. To reduce this risk:

• Carefully follow all instructions and warnings on the battery

label and package and accompanying Battery Safety

Leaet.

• Always insert batteries correctly with regard to polarity

(+ and –), marked on the battery and the equipment.

• Do not short battery terminals.

• Do not charge disposable batteries.

• Do not mix old and new batteries. Replace all of them at the

same time with new batteries of the same brand and type.

• Remove dead batteries immediately and dispose of per

local codes.

• Do not dispose of batteries in re.

• Keep batteries out of reach of children.

• Remove batteries when the device is not in use

• Use only the charger specied for your rechargeable

battery pack.

Personal Safety

• Stay alert, watch what you are doing and use common

sense when operating a laser tool. Do not use tool while

tired or under the inuence of drugs, alcohol, or medication.

A moment of inattention while operating power tools may

result in serious personal injury.

• Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

Service

• Tool service must be performed only by qualied repair

personnel. Service or maintenance performed by unqualied

personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement

parts. Follow instructions in the Maintenance section of

this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of electric shock

or injury.

To locate your nearest DeWALT service center go to

http://www.2helpU.com on the Internet.

Operating Tips

• Use only new, high-quality, name brand AA batteries or

specied rechargeable DEWALT10.8V Li-Ion pack for best

results.

• Ensure batteries are in good working condition. If the low

battery red indicator light is ashing, the batteries need

replacement.

• To extend battery life, turn laser off when not working with or

marking the beam.

• To ensure the accuracy of your work, check to make sure

your laser is calibrated often. See Field Calibration Check.

• Before attempting to use the laser, make sure it is

positioned securely, on a smooth, at surface.

• Always mark the center of the beam created by the laser.

• Extreme temperature changes may cause movement of

internal parts that can affect accuracy. Check your accuracy

often while working. See Field Calibration Check.

• If the laser has been dropped, check to make sure your

laser is still calibrated. See Field Calibration Check.

• Place the laser on a smooth, at, stable surface that is level

in both directions.

Low Battery Indication

The DCE089G, DCE089R, DCE0811G and DCE0811R lasers

are equipped with a battery gauge as shown in Figure 1B.

The battery gauge indicates remaining power with each LED

representing 25%. The bottom LED will illuminate and blink

indicating that the level is low (below 12.5%) and the batteries

need to be replaced. The laser may continue to operate for

a short time while the batteries continue to drain, but the

beam(s) will quickly dim. After fresh batteries are installed

and the laser is turned on again, the laser beam(s) will return

to full brightness and the battery indicator level will indicate

full capacity. (A ashing laser beam is not caused by low

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCE0811R Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info