Bedienungsanleitung DeWalt DCE0825G (Seite 9 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790836

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Charging the DeWALT Li-ion Battery

1. If the 10.8V Li-ion battery pack is attached to the laser, remove

it (Figure D).

• Rotate the laser so it is easier to access the battery pack

(Figure D #1).

• While pressing down on the release button on the battery

pack (Figure D #2), pull the battery pack up to unlock

it from the laser (Figure D #3).

• Pull the battery pack the rest of the way up and out of the

laser (Figure D #4).

2. Plug the charger cord into an electrical outlet.

3. Slide the battery pack into the charger until it snaps in place

(Figure F #1). On the charger, the left indicator light will flash

to let you know the battery is being charged (Figure F #2).

4. After the battery is fully-charged (the indicator light on the

charger no longer flashes), press and hold the release button

on the battery pack (Figure F #3) and slide the pack out

of the charger (Figure F #4).

5. Slide the battery pack down in the laser until it snaps in place

(Figure F #5).

Installing New AA Batteries

CAUTION:

The AA Starter Pack is designed specically for use

with DeWALT 10.8V compatible laser products and

cannot be used with any other tools. Do not attempt

to modify the product.

1. If the AA Starter Pack is attached to the laser, remove it (Figure

D).

• Rotate the laser so it is easier to access the Starter Pack

(Figure D #1).

• While pressing down on the release button on the Starter

Pack (Figure D #2), pull the Starter Pack up to unlock

it from the laser (Figure D #3).

• Pull the Starter Pack the rest of the way up and out of the

laser (Figure D #4).

2. On the AA Starter Pack, lift up the latch to open the battery

compartment cover (Figure E #1 and #2).

3. Insert four new, high-quality, name brand AA batteries, making

sure to position the - and + ends of each battery as noted inside

the battery compartment (Figure E #3).

4. Push the battery compartment cover down until it snaps in

place.

5. Slide the Starter Pack down in the laser until it snaps in place

(Figure E #4).

Viewing the Battery Meter on the Keypad

When the laser is ON, the battery meter on the keypad (Figure A

#3) indicates how much power remains. Each of the four LEDs

on the battery meter represents 25% of the power.

• The bottom LED will illuminate and ash when the battery

level is low (below 12.5%). The laser may continue to operate

for a short time while the battery power continues to drain,

but the beam(s) will quickly dim.

• After fresh batteries are installed in the AA Starter Pack, or

the 10.8V Li-ion battery is charged, and the laser is turned

ON again, the laser beam(s) will return to full brightness and

the battery indicator level will indicate full capacity.

• If all 4 LEDs on the battery meter remain ON, this indicates

that the laser is not fully powered OFF. When the laser is not

in use, make sure the Power/Transport Lock switch is placed

to the LEFT to the Locked/OFF position (Figure A #1a).

Turning the Laser On

1. Place the laser on a smooth, flat surface.

2. Slide the Power/Transport Lock switch to the right to the

Unlocked/ON position (Figure A #1b).

3. Press each button on the keypad (Figure A #3) to test

each laser beam setting.

• Press once to display a horizontal laser line (Figure A

#3a), a second time to display a vertical laser line (Figure

A #3b), a third time to display a horizontal line and

a vertical line (Figure A #3c), and a fourth time to stop

displaying laser lines.

• Press once to display dots above, ahead, and below

the laser (Figure A #3d), a second time to display two

additional dots from either side of the laser (Figure A

#3e), and a third time to stop displaying dots.

• You can use and together to display laser dots

and lines. For example, if you press three times and

twice, the laser will display cross lines and five dots

(Figure A #3f).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCE0825G Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info