Bedienungsanleitung DeWalt DCE089R (Seite 11 von 126) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790842

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

Maintenance

• To maintain the accuracy of your work, check the laser often

to make sure it is properly calibrated. See Field Calibration

Check.

• Calibration checks and other maintenance repairs may be

performed by DeWALT service centers.

• When not in use, store the laser in the kit box provided. Do

not store your laser at temperatures below -20 ˚C (-5 ˚F ) or

above 60 ˚C (140 ˚F).

• Do not store your laser in the kit box if the laser is wet.

The laser should be dried rst with a soft dry cloth prior to

storage.

Cleaning

Exterior plastic parts may be cleaned with a damp cloth.

Although these parts are solvent resistant, NEVER use

solvents. Use a soft, dry cloth to remove moisture from the tool

before storage.

Accuracy Check and

Calibration

Checking Accuracy –

Horizontal Beam - Scan Direction (See gure 7)

Checking the horizontal scan calibration of the laser requires

two walls 9m (30’) apart. It is important to conduct a calibration

check using a distance no shorter than the distance of the

applications for which the tool will be used.

1. Place the laser on a smooth, at, stable surface that is

level in both directions, with the laser facing straight ahead

toward the opposing wall (0 degree position).

2. Turn on the laser’s horizontal beam and pivot the laser

toward the opposite end of the wall and approximately

parallel to the adjacent wall (Figure 7 #1).

3. Mark the center of the beam at two locations ( a, b) at

least 30’ (9m) apart.

4. Pivot the laser 180 º on the bracket, and mark the horizontal

beam position on the opposing wall c (Figure 7 #2).

5. Measure the vertical distance between b and c. If the

measurement is greater than the values shown below, the

laser must be serviced at an authorized service center.

Distance Between Walls

Allowable Distance

Between b and c

9 m (30’) 6.0 mm (1/4”)

12 m (40’) 8.0 mm (5/16”)

15 m (50’) 10.0 mm (13/32”)

6. Rotate the laser 90 º and repeat the test.

Checking Accuracy –

Horizontal Beam - Pitch Direction (See gure 8)

Checking the horizontal pitch calibration of the laser

requires a single wall at least 30’ (9m) long. It is important

to conduct a calibration check using a distance no shorter

than the distance of the applications for which the tool

will be used.

1. Place the laser on a smooth, at, stable surface that is level

in both directions and against the end of a 30’ (9m) wall.

2. Turn on the laser’s horizontal beam and pivot the laser

toward the opposite end of the wall and approximately

parallel to the adjacent wall (Figure 8 #1).

3. Mark the center of the beam at two locations ( a, b) at

least 30’ (9m) apart.

4. Reposition the laser to the opposite end of the wall (Figure

8 #2).

5. Turn on the laser’s horizontal beam and pivot the laser back

toward the rst end of the wall and approximately parallel to

the adjacent wall.

6. Adjust the height of the laser so that the center of the beam

is aligned with the nearest mark b.

7. Mark the center of the beam c directly above or below the

farthest mark a.

8. Measure the distance between a and c. If the

measurement is greater than the values shown below, the

laser must be serviced at an authorized service center.

Distance Between Walls

Allowable Distance

Between a and c

9 m (30’) 6.0 mm (1/4”)

12 m (40’) 8.0 mm (5/16”)

15 m (50’) 10.0 mm (13/32”)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCE089R Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info