Bedienungsanleitung DeWalt DCF610 T 2 (Seite 36 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549688

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

ENGLISH

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the main

handle (e).

Variable Speed Trigger Switch (ﬁ g. 1)

To turn the tool on, squeeze the trigger switch (a).

To turn the tool off, release the trigger switch. Your

tool is equipped with a brake. The chuck will stop as

soon as the trigger switch is fully released.

The variable speed switch enables you to start

the application at a slow speed. The further you

squeeze the trigger, the faster the tool will operate.

For maximum tool life, use variable speed only for

starting holes or fasteners.

NOTE: Continuous use in variable speed range is

not recommended. It may damage the switch and

should be avoided.

Forward/Reverse Control Button

(ﬁ g. 1)

A forward/reverse control button (b) determines the

direction of the tool and also serves as a lock-off

button.

To select forward rotation, release the trigger switch

and depress the forward/reverse control button on

the right side of the tool.

To select reverse, depress the forward/reverse

control button on the left side of the tool. The center

position of the control button locks the tool in the off

position. When changing the position of the control

button, be sure the trigger is released.

NOTE: The first time the tool is run after changing

the direction of rotation, you may hear a click on

start up. This is normal and does not indicate a

problem.

Worklights (ﬁ g. 1)

There are three worklights (h) located around the

chuck collar (d). The worklight will be activated when

the trigger switch is squeezed.

NOTE: The worklight is for lighting the immediate

work surface and is not intended to be used as a

flashlight.

Torque Adjustment Collar (ﬁ g. 1)

The torque adjustment collar (c) is clearly marked

with numbers and the max position.The collar should

be rotated until the desired setting is located at the

top of the tool. Locators are provided in the collar to

eliminate the guess work when selecting fastening

torque. The higher the number on the collar, the higher

the torque and the larger the fastener which can be

driven. To lock the clutch for drilling operations, move

to the max position.

Quick-Release Chuck (ﬁ g. 1, 4)

NOTE: The chuck accepts 1/4" (6.35mm) hex

accessories or 1" (25.4mm) bit tips only. Using 1"

(25.4mm) bits allows better access in tight spaces.

Place the forward/reverse button (b) in the locked

off (center) position or remove battery pack before

changing accessories.

The bit shown in Figure 4 is typical of the bits for use

in the quick-release chuck with a groove (l) which is

required to hold the bit firmly.

To install an accessory, push accessory to fully

insert into chuck. The chuck collar does not need to

be pulled up to lock accessory in place.

To remove an accessory, pull the chuck collar

away from the front of the tool. Remove the

accessory and release the collar.

Screwdriver Mode (ﬁ g. 1)

Select the desired torque number using the torque

adjustment collar (c) on the top of tool.

Insert the desired fastener accessory into the chuck

as you would any screwdriver bit. Make a few

practice runs in scrap or unseen areas to determine

the proper position of the clutch collar.

Drilling Mode

WARNING: To reduce the risk

of serious personal injury, place

the forward/reverse button in

the lock-off position or turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories.

WARNING: To reduce the risk of

personal injury, ALWAYS ensure

workpiece is anchored or clamped

firmly. If drilling thin material, use a wood

“back-up” block to prevent damage to

the material.

Turn the collar to the max position symbol for drilling.

1. Use hex shank drill bits only.

2. Always apply pressure in a straight line with the

bit. Use enough pressure to keep the bit biting,

but do not push hard enough to stall the motor

or deflect the bit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCF610 T 2 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info