Bedienungsanleitung DeWalt DCF620 (Seite 38 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

652171

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

2. Slide the battery pack firmly into the handle until

you hear the lock snap into place.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the release button (e) and firmly pull the

battery pack out of the tool handle.

2. Insert battery pack into the charger as

described in the charger section of this manual.

FUEL GAUGE BATTERY PACKS (FIG. 2)

Some D

EWALT battery packs include a fuel gauge

which consists of three green LED lights that

indicate the level of charge remaining in the battery

pack.

To actuate the fuel gauge, press and hold the fuel

gauge button (t). A combination of the three green

LED lights will illuminate designating the level of

charge left. When the level of charge in the battery

is below the usable limit, the fuel gauge will not

illuminate and the battery will need to be recharged.

NOTE: The fuel gauge is only an indication of the

charge left on the battery pack. It does not indicate

tool functionality and is subject to variation based

on product components, temperature and end-user

application.

Changing Bit Holders (ﬁ g. 3)

1. Rotate the locking collar (c) 1/4 turn to unlock

nose cone from gear case.

2. Pull nose cone (d) off of gear case.

3. To remove:

a. Grab the bit holder (v).

b. Push it into the gear case depressing the

sleeve (u).

c. Rotate the bit holder until the clutch

engages.

d. While holding the sleeve depressed, pull the

bit holder out.

4. Push and rotate the new bit holder into

gearcase, depressing the sleeve, until ball lock

snaps in groove in bit holder shank.

5. Replace nose cone (d) by placing on gear case

and rotating collar 1/4 turn to align arrow on

gear case with the lock symbol on collar.

Changing Bit Tip (ﬁ g. 3)

1. Rotate the locking collar (c) ¼ turn to unlock

nose cone from gear case.

2. Pull forward on nose cone (d) and remove it

from clutch housing.

3. Use pliers to remove worn bit and install new bit

tip.

Your DEWALT charger is double insulated

in accordance with EN 60335; therefore

no earth wire is required.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DEWALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 3 A.

Using an Extension Cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see Technical Data). The minimum conductor size

is 1 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: Prior to assembly and

adjustment, always remove the battery

pack. Always switch off the tool before

inserting or removing the battery pack.

WARNING: Use only DEWALT battery

packs and chargers.

Inserting and Removing the

Battery Pack from the Tool (ﬁ g. 2)

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up

can cause injury.

NOTE: Make sure your battery pack (f) is fully

charged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the notch inside the tool’s handle with the

battery pack (fig. 2).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCF620 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info