Bedienungsanleitung DeWalt DCF830 T 1 (Seite 39 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

550335

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

WARNING: To reduce the risk of

serious personal injury, ensure the

screw holding the belt hook is secure.

IMPORTANT: When attaching or replacing the

belt hook or bit clip, use only the screw (i) that is

provided. Be sure to securely tighten the screw.

The belt hook (h) and bit clip (j) can be be attached

to either side of the tool using only the screw (i)

provided, to accommodate left- or right- handed

users. If the hook or bit clip is not desired at all, it

can be removed from the tool.

To move belt hook or bit clip, remove the screw

(i) that holds it in place then reassemble on the

opposite side. Be sure to securely tighten the screw.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, place

the forward/reverse button in

the lock-off position or turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up

can cause injury.

Proper Hand Position (ﬁ g. 1, 4)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the main

handle (k).

Variable Speed Trigger Switch (ﬁ g. 1)

To turn the tool on, squeeze the trigger switch (a). To

turn the tool off, release the trigger switch. Your tool

is equipped with a brake. The chuck will stop when

the trigger switch is fully released.

The variable speed switch enables you to start

the application at a slow speed. The further you

squeeze the trigger, the faster the tool will operate.

For maximum tool life, use variable speed only for

starting holes or fasteners.

NOTE: Continuous use in variable speed range is

not recommended. It may damage the switch and

should be avoided.

Forward/Reverse Control Button

(ﬁ g. 1)

A forward/reverse control button (b) determines the

direction of the tool and also serves as a lock-off

button.

To select forward rotation, release the trigger switch

and depress the forward/reverse control button on

the right side of the tool.

To select reverse, depress the forward/reverse

control button on the left side of the tool. The center

position of the control button locks the tool in the off

position. When changing the position of the control

button, be sure the trigger is released.

NOTE: The first time the tool is run after changing the

direction of rotation, you may hear a click on start up.

This is normal and does not indicate a problem.

Worklights (ﬁ g. 1)

There are three worklights (g) located around the

chuck collar (c). The worklights will be activated

when the trigger switch is squeezed.

When the trigger is released the worklight will stay

illuminated for up to 20 seconds.

NOTE: The worklights are for lighting the immediate

work surface and are not intended to be used as a

flashlight.

Quick-Release Chuck (ﬁ g. 1, 3)

DCF835, DCF885

NOTE: The chuck accepts 6.35mm (1/4") hex

accessories and 25.4mm (1") bit tips only. Using

25.4mm (1") bits allows better access in tight

spaces.

Place the forward/reverse button (b) in the locked

off (center) position or remove battery pack before

changing accessories.

To install an accessory, push accessory to fully insert

into chuck. The chuck collar does not need to be

pulled up to lock accessory in place.

To remove an accessory, pull the chuck collar away

from the front of the tool. Remove the accessory

and release the collar.

Anvil with Detent Pin (Fig. 1)

DCF830, DCF880

Place the switch in the locked off (center) position or

remove battery pack before changing accessories.

To install a socket on the anvil, align the hole in the

side of the socket with the detent pin (m) on the

anvil (l). Press the socket on until the detent pin

engages in the hole. Depression of detent pin may

be necessary to aid installation of socket.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCF830 T 1 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DCF830 T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info