Bedienungsanleitung DeWalt DCF889 T 2 (Seite 38 von 168) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

551246

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

ENGLISH

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the main

handle (d).

Variable Speed Trigger Switch (ﬁ g. 1)

To turn the tool on, squeeze the trigger switch

(a). To turn the tool off, release the trigger switch.

Your tool is equipped with a brake. The anvil will

stop when the trigger switch is fully released. The

variable speed switch enables you to select the best

speed for a particular application. The more you

squeeze the trigger, the faster the tool will operate.

For maximum tool life, use variable speed only for

starting holes or fasteners.

NOTE: Continuous use in variable speed range is

not recommended. It may damage the switch and

should be avoided.

Forward/Reverse Control Button

(ﬁ g.1)

A forward/reverse control button (b) determines the

direction of the tool and also serves as a lock-off

button.

To select forward rotation, release the trigger switch

and depress the forward/reverse control button on

the right side of the tool.

To select reverse, release the trigger switch and

depress the forward/reverse control button on the

left side of the tool.

The center position of the control button locks the

tool in the off position. When changing the position

of the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing

the direction of rotation, you may hear a click on

start up. This is normal and does not indicate a

problem.

Worklight (ﬁ g. 1)

There is a worklight (g) located on the foot of the

tool. The worklight is activated when the trigger

switch is depressed. When the trigger is released,

the worklight will stay illuminated for up to 20

seconds.

NOTE: The worklight is for lighting the immediate

work surface and is not intended to be used as a

flashlight.

Anvil (ﬁ g. 2)

WARNING: Use only impact

accessories. Non-impact accessories

may break and cause a hazardous

condition. Inspect accessory prior to

use to ensure that it contains no cracks.

CAUTION: Inspect anvils, detent pins,

and hog rings prior to use. Missing or

damaged items should be replaced

before use.

Place the switch in the locked off (center) position or

remove battery pack before changing accessories.

ANVIL WITH DETENT PIN (FIG. 2)

To install an accessory on the anvil, align the hole in

the side of the accessory with the detent pin (h) on

the anvil (c). Press the accessory on until the detent

pin engages in the hole. Depression of detent pin

may be necessary to aid installation of accessory.

To remove an accessory, depress the detent pin

through the hole and pull the accessory off.

ANVIL WITH HOG RING (FIG. 3)

DCF889H

To install an accessory on the hog ring anvil, firmly

push accessory onto the anvil (c). The hog ring (i)

compresses to allow the accessory to slide on. After

accessory is installed, the hog ring applies pressure

to help provide accessory retention.

To remove an accessory, grasp the accessory and

firmly pull it off.

Usage

Your impact tool can generate the following

maximum torque:

Cat # Nm Ft.-Lbs. In.-Lbs.

DCF889 540 400 4800

DCF889H 540 400 4800

WARNING: Ensure fastener and/

or system will withstand the level

of torque generated by the tool.

Excessive torque may cause

breakage and possible personal

injury.

1. Place the accessory on the fastener head. Keep

the tool pointed straight at the fastener.

2. Press switch to start operation. Release switch

to stop operation. Always check torque with

a torque wrench, as the fastening torque is

affected by many factors including the following:

• Voltage: Low voltage, due to a nearly

discharged battery, will reduce fastening

torque.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCF889 T 2 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info