Bedienungsanleitung DeWalt DCF895 (Seite 38 von 168) (Alle Sprachen)

723569

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

ENGLISH

WARNING: To reduce the risk

of serious personal injury, place

the forward/reverse button in

the lock-off position or turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories.

Proper Hand Position (ﬁ g. 1, 3)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the main

handle (k).

Variable Speed Trigger Switch (ﬁ g. 1)

To turn the tool on, squeeze the trigger switch (a). To

turn the tool off, release the trigger switch. Your tool

is equipped with a brake. The tool will stop when the

trigger switch is fully released.

The variable speed switch enables you to start

the application at a slow speed. The further you

squeeze the trigger, the faster the tool will operate.

For maximum tool life, use variable speed only for

starting holes or fasteners.

NOTE: Continuous use in variable speed range is

not recommended. It may damage the switch and

should be avoided.

Forward/Reverse Control Button

(ﬁ g. 1)

A forward/reverse control button (b) determines the

direction of the tool and also serves as a lock-off

button.

To select forward rotation, release the trigger switch

and depress the forward/reverse control button on

the right side of the tool.

To select reverse, release the trigger switch (a) and

depress the forward/reverse control button on the

left side of the tool. The center position of the control

button locks the trigger switch (a) in the off position.

When changing the position of the control button,

be sure the trigger is released.

NOTE: The first time the tool is run after changing the

direction of rotation, you may hear a click on start up.

This is normal and does not indicate a problem.

Worklights (ﬁ g. 1)

There are three worklights (g) located around the

6.35 mm (1/4") hex chuck (d). The worklights are

activated when the trigger switch is depressed.

When the trigger is released, the worklight will stay

illuminated for up to 20 seconds.

NOTE: The worklights are for lighting the immediate

work surface and are not intended to be used as a

flashlight.

Speed Selector (ﬁ g. 1, 4)

Your tool is equipped with a speed selector (j) which

allows you to select one of three speeds. Select

the speed based on the application and control the

speed of the tool using the variable speed trigger

switch (a).

DCF825 DECF895

Speed 1 rpm 0–900 0–950

Speed 2 rpm 0–1850 0–1900

Speed 3 rpm 0–2800 0–2850

Accessory Insertion and Release

(ﬁ g. 1, 5, 6)

NOTE: These tools only accept 6.35 mm (1/4") hex

accessories.

To install an accessory, fully insert the accessory into

the chuck (d). The accessory is locked into place

(fig. 5).

To remove an accessory, push on the accessory

release button (c). Remove the accessory then

release the accessory release button (fig. 6).

Usage

Your impact tool generates the following maximum

torque:

Cat # Nm

DCF825 160

DCF895 170

CAUTION: Ensure fastener and/or

system will withstand the level of torque

generated by the tool. Excessive torque

may cause breakage and possible

personal injury.

1. Place the socket on the fastener head. Keep

the tool pointed straight at the fastener.

2. Press switch to start operation. Release the

switch to stop operation. Always check torque

with a torque wrench, as the fastening torque is

affected by many factors including the following:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCF895 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info