712257
14
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
12
English
WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed and
securely tightened. Failure to do so may result in the side handle
slipping during tool operation and subsequent loss of control. Hold
tool with both hands to maximizecontrol.
Installing and Removing the Battery Pack
(Fig. 7)
WARNING: To reduce the risk of injury, never depress the battery
release button without removing the battery pack. Depressing the
battery release button without removing the battery pack can result
in the battery pack falling outunexpectedly.
NOTE: For best results, make sure your battery pack is fullycharged.
To install the battery pack (G) into the tool handle, align the battery
pack with the rails inside the tool’s handle and slide it into the handle
until the battery pack is firmly seated in the tool and ensure that it does
notdisengage.
G
FIG. 7
H
To remove the battery pack from the tool, press the release button (H)
and firmly pull the battery pack out of the tool handle. Insert it into the
charger as described in the charger section of thismanual.
FIG. 5
C
LOCKED
UNLOCKED,
REVERSE
UNLOCKED,
FORWARD
Worklight (Fig. 6)
CAUTION: Do not stare into worklight. Serious eye injury could
result.
There is a worklight (F) located on the front
FIG. 6
F
of the tool. The worklight is activated
when the trigger switch is depressed, and
will automatically turn off 20 seconds after
the trigger switch is released. If the trigger
switch remains depressed, the worklight
will remainon.
NOTE: The worklight is for lighting the
immediate work surface and is not intended to be used as aflashlight.
OPERATION
WARNING: To reduce the risk of serious personal injury, turn
tool off and disconnect tool from power source before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can causeinjury.
WARNING: To reduce the risk of personal injury, ALWAYS
ensure workpiece is anchored or clamped firmly. If drilling thin
material, use a wood "back-up" block to prevent damage to
thematerial.
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt DCH253 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info