Bedienungsanleitung DeWalt DCH334 (Seite 11 von 40) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

712244

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Installing and Removing the Battery Pack

(Fig. F)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack

1

into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide

it into the handle until the battery pack is firmly seated in

the tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button

2

and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

Fig.F

Proper Hand Position (Fig. G)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.



WARNING: To reduce the risk of serious personal injury,

ALWAYS hold securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side handle,

with the other hand on the mainhandle. Hold tool firmly

with both hands to control the twisting action of the drill.

Fig. G

Overload Clutch

In case of jamming of a drill bit, the drive to the drill spindle

is interrupted by the overload clutch. Due to the resulting

forces, always hold the tool with both hands and take a

firmstance. After the overload, release and depress the

trigger to re-engage drive.



WARNING: Drill may stall if overloaded causing a

sudden twist. Always expect the stall. Grip the drill

firmly to control the twisting action and avoidinjury.

Operation Modes (Fig. H)



WARNING: Do not select the operating mode when

the tool isrunning.



CAUTION: Never use in Rotary Drilling or Rotary

Hammering mode with a chisel bit in the bit holder.

Personal injury and damage to the the tool may result.

Your tool is equipped with a mode selector dial 

6

selectthe mode appropriate to desired operation.

Symbol Mode Application

Rotary Drilling

Screwdriving

Drilling into steel, wood

andplastics

Rotary

Hammering

Drilling into concrete

and masonry

Hammering

only

Lightchipping

To select an operating mode:

1. Depress the mode selector release button

7

2. Rotate the mode selector dial so that the arrow points to

the symbol corresponding for the desired mode.

Fig. H

NOTE: The arrow on the mode selector dial

6

must be

pointing at a mode symbol at all times. There are no

operable positions inbetween. It may be necessary to briefly

run the motor after having changed from 'hammering only'

to 'rotary' modes in order to align thegears.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCH334 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info