Bedienungsanleitung DeWalt DCH481 (Seite 33 von 144) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790948

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

ENGLISH

Anti-Rotation System (Fig. D)

In addition to the clutch, an anti-rotation system offers increased

user comfort and safety through an on-board, anti-rotation

technology capable of detecting if the user loses control of

thehammer. When a jam is detected, the torque and speed are

reducedinstantly. This feature prevents self rotation of the tool

reducing the occurrence of wristinjuries.

The anti-rotation system indicator 11 will illuminate to

indicatestatus.

Indicator Diagnosis Solution

OFF Tool is functioning

normally

Follow all warnings and instructions

when operating the tool.

SOLID Anti-Rotation

System has

been activated

(ENGAGED)

With the tool properly supported,

release trigger. The tool will function

normally when the trigger is depressed

again and the indicator light will go out

Active Vibration Control

For best vibration control, hold the tool as described in Proper

HandPosition.

The active vibration control neutralises rebound vibration from

the hammer mechanism. Lowering hand and arm vibration,

it allows more comfortable use for longer periods of time and

extends the life of theunit.

The hammer only needs enough pressure to engage the active

vibraton control. Applying too much pressure will not make

the tool drill or chip faster and active vibration control will

notengage.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

WARNING: Use only

DeWALT

battery packs andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig. B)

NOTE: Make sure your battery pack 1 is fullycharged.

To Install the Battery Pack into the Tool

Handle

1. Align the battery pack 1 with the rails inside the tool’s

handle (Fig. B).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button 2 and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button12. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level

of charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Side Handle (Fig. A)

WARNING: To reduce the risk of personal injury, ALWAYS

operate the tool with the side handle properly installed.

Failure to do so may result in the side handle slipping

during tool operation and subsequent loss of control. Hold

tool with both hands to maximizecontrol.

The side handle3 clamps to the front of the gear case and

may be rotated 360˚ to permit right- or left-hand use. The side

handle must be tightened sufficiently to resist the twisting

action of the tool if the accessory binds or stalls. Be sure to grip

the side handle at the far end to control the tool during astall.

To loosen side handle, rotatecounterclockwise.

Bit and Bit Holder

WARNING: Burn Hazard. ALWAYS wear gloves when

changing bits. Accessible metal parts on the tool and bits

may get extremely hot during operation. Small bits of

broken material may damage barehands.

The hammerdrill can be fitted with different bits depending on

the desired application. Use sharp drill bitsonly.

SDS-Max Bit Holder (Fig. A, C, F)

To insert a drill bit or other accessory:

1. Insert the shank of the bit about 19mm into SDS-Max tool

holder8.

2. Push and rotate bit until it locks in place. The bit will be

securelyheld.

3. To release bit, pull the sleeve9 back and remove thebit.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and

applicableregulations.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig. F)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCH481 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info