Bedienungsanleitung DeWalt DCM565 (Seite 42 von 216) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

712343

Zoom out

Zoom in

Vorherige Seite

1/216

Nächste Seite

ENGLISH

• Use extreme caution when cutting small size brush and

saplings because slender material may catch the saw chain

and be whipped toward you or pull you offbalance.



WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities

contains chemicals known to the State of California to

cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• a

rsenic and chromium from chemically-treatedlumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed

to filter out microscopicparticles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth, eyes, or lay

on the skin may promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/or disburse

dust, which may cause serious and permanent respiratory

or other injury.

Chainsaw Names and Terms

• Bucking - The process of cross cutting a felled tree or log intolengths.

• Motor Brake - A device used to stop the saw chain when the

trigger isreleased.

• Chain Saw Powerhead - A chain saw without the saw chain

and guidebar.

• Drive Sprocket or Sprocket - The toothed part that drives the

sawchain.

• Felling - The process of cutting down atree.

• Felling Back Cut - The final cut in a tree felling operation made

on the opposite side of the tree from the notchingcut.

• Front Handle - The support handle located at or toward the

front of the chainsaw.

• Front Hand Guard - A structural barrier between the front

handle of a chain saw and the guide bar, typically located

close to the hand position on the fronthandle.

• Guide Bar - A solid railed structure that supports and guides

the sawchain.

• Guide Bar Scabbard - Enclosure fitted over guide bar to prevent

tooth contact when saw is not inuse.

• Kickback - The backward or upward motion, or both of the guide

bar occurring when the saw chain near the nose of the top area

of the guide bar contacts any object such as a log or branch, or

when the wood closes in and pinches the saw chain in thecut.

• Kickback, Pinch - The rapid pushback of the saw which can

occur when the wood closes in and pinches the moving saw

chain in the cut along the top of the guidebar.

• Kickback, Rotational - The rapid upward and backward

motion of the saw which can occur when the moving saw

chain near the upper portion of the tip of the guide bar

contacts an object, such as a log orbranch.

• Limbing - Removing the branches from a fallen tree

• Low-Kickback Chain - A chain that reduces the kickback

performance requirements. (when tested on a representative

sample of chain saws.)

• Normal Cutting Position - Those positions assumed in

performing the bucking and fellingcuts.

• Notching Undercut - A notch cut in a tree that directs the tree’sfall.

• Rear Handle - The support handle located at or toward the

rear of thesaw.

• Reduced Kickback Guide Bar - A guide bar which has been

demonstrated to reduce kickbacksignificantly.

• Replacement Saw Chain - A chain that reduces the kickback

performance requirements when tested with specific

chainsaws.

• Saw Chain - A loop of chain having cutting teeth, that cut the

wood,and that is driven by the motor and is supported by the

guidebar.

• Ribbed Bumper - The ribs used when felling or bucking to pivot

the saw and maintain position whilesawing.

• Switch - A device that when operated will complete or interrupt

an electrical power circuit to the motor of the chainsaw.

• Switch Linkage - The mechanism that transmits motion from

a trigger to theswitch.

• Switch Lockout - A movable stop that prevents the

unintentional operation of the switch until manuallyactuated.

Intended Use

Your

DeWALT

DCM565 Chainsaw is ideal for pruning

applications and cutting logs up to 26cm indiameter.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

Your

DeWALT

charger is double insulated in

accordance with EN60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the

DeWALT

serviceorganisation.

DeWalt DCM565 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info