Bedienungsanleitung DeWalt DCMW564 (Seite 43 von 184) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

712289

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

ENGLISH

4. Install sharpened or new blade

29

on shoulder

31

of the

blade fan

30

as shown in Fig. P.

NOTE: When replacing sharpened or new blade on shoulder

of blade fan

30

, make sure the “GRASS SIDE” on the blade will

be facing the ground when the mower is returned to its normal

upright position.

5. Install the plastic blade insulator

28

on the blade such that

the raised lips on one side engage the edges of the blade.

6. Install the blade spacer

27

so that it sits inside the raised

lips on the other side of the blade insulator. Be sure to align

the flats in the hole of the blade spacer with the flats of

the shaft, rotating the blade and blade insulator together

asnecessary.

7. Position piece of wood

24

to keep blade from turning

as shown in Fig. Q. Install flange nut

25

with the flange

against the blade spacer

27

and securely tighten with

awrench.

Blade Sharpening

KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A DULL

BLADE DOES NOT CUT GRASSCLEANLY.

• DCMW564 requires replacement blade DT20671.

The use of accessories not recommended in this manual

may be hazardous.



WARNING: Use gloves and proper eye protection while

removing, sharpening, and installing blade. Ensure that

safety key and battery packs are removed.

Sharpening the blade twice during a mowing season is usually

sufficient under normal circumstances. Sand causes the blade

to dull quickly. If your lawn has sandy soil, more frequent

sharpening may berequired. REPLACE BENT OR DAMAGED

BLADEIMMEDIATELY.

When Sharpening the Blade

• Make sure blade remainsbalanced.

• Sharpen blade at the original cuttingangle.

• Sharpen cutting edges on both ends of blade, removing

equal amounts of material from bothends.

To Sharpen Blade in a Vice (Fig. R)

1. Be sure the bail handle is released, the blade has stopped

and safety key and battery packs are removed before

removing theblade.

2. Remove blade from mower. See instructions for Removing

and InstallingBlade.

3. Secure blade

29

in a vice

32

4. Wear proper eye protection and gloves and be careful not

to cutyourself.

5. Carefully file the cutting edges of the blade with a fine-tooth

file

33

or sharpening stone, maintaining the angle of the

original cuttingedge.

6. Check balance of blade. See instructions for

BladeBalancing.

7. Replace blade on mower and tightensecurely.

Blade Balancing (Fig. S)

Check balance of the blade

29

by placing centre hole in the

blade over a nail or round screwdriver

34

, clamped horizontally

in a vice

32

. If either end of the blade rotates downward, file

along the sharp edge of that dropping end. Blade is properly

balanced when neither enddrops.

Lubrication

No lubrication is necessary. Do not oil the wheels. They have

plastic bearing surfaces which require nolubrication.

Cleaning

Release bail handle

5

to turn mower off, let the blade come

to a stop and then remove safety key. Clean out any clippings

which may have accumulated on the underside of the deck.

After several uses, check all exposed fasteners fortightness.



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Preventing Corrosion

Fertilizers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals. If you mow in areas

where fertilizers or chemicals have been used, the mower

should be cleaned immediately afterward as follows: Release

bail handle

5

to turn mower off and unplug safety key. Wipe all

exposed parts with a dampcloth.

Optional Accessories



WARNING: Since accessories, other than those offered

DeWALT

, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only

DeWALT

recommended

accessories should be used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCMW564 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info