Bedienungsanleitung DeWalt DCR027 (Seite 7 von 14) (Englisch)

712268

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

ENGLISH

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting toclean.

• DO NOT attempt to charge the battery pack with any

charger/radio other than the one in this manual.

The charger and battery pack are specifically designed to

worktogether.

• These charger/radios are not intended for any uses other

than charging

DeWALT

rechargeable batteries. Any other

uses may result in risk of fire, electric shock orelectrocution.

• Do not expose charger/radio to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk of damage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire, electric shock, orelectrocution.

• Do not place any object on top of charger/radio or place

the charger/radio on a soft surface that might block

the ventilation slots and result in excessive internal

heat. Place the charger/radio in a position away from any

heatsource.

• Do not operate charger/radio with damaged cord or

plug — have them replacedimmediately.

• Do not operate charger/radio if it has received a sharp

blow, been dropped, or otherwise damaged in any way.

Take it to an authorised servicecentre.

• Do not disassemble charger/radio; take it to an

authorised service centre when service or repair is

required. Incorrect reassembly may result in a risk of electric

shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• Your charger/radio is designed to operate on standard

230 V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharge.

Charging a Battery (Fig. A, B)

When the charger/radio is plugged in it will charge the installed

battery. Unplugged, the radio will run up to 8 hours on a fully

charged battery using a premium 18V Li-Ion battery. Using

batteries of lower amp hours will yield less runtime.

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack

19

into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light

12

will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

To remove the battery pack from the charger, push the

battery release button

20

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. Once the temperature has warmed, it will charge

at a higherrate.

Electronic Protection System

XR Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium-ion battery

pack on the charger until it is fullycharged.

Charger/Radio Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non-metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

Battery Packs

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCR027 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info