Bedienungsanleitung DeWalt DCS331 (Seite 43 von 184) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546388

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

ENGLISH

DO NOT let children come into contact with the

tool. Supervision is required when inexperienced

operators use this tool.

• This product is not intended for use by persons

(including children) suffering from diminished

physical, sensory or mental abilities; lack of

experience, knowledge or skills unless they are

supervised by a person responsible for their

safety. Children should never be left alone with

this product.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the battery pack

voltage corresponds to the voltage on the rating

plate. Also make sure that the voltage of your

charger corresponds to that of your mains.

Your DEWALT charger is double insulated

in accordance with EN 60335; therefore

no earth wire is required.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DEWALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 3 A.

Using an Extension Cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see Technical Data). The minimum conductor size

is 1 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENT

WARNING: To reduce the risk of

serious personal injury, depress the

trigger lock button and disconnect

battery pack before making any

adjustments or removing/installing

attachments or accessories. An

accidental start-up can cause injury.

WARNING: Use only DEWALT battery

packs and chargers.

Inserting and Removing the

Battery Pack from the Tool (ﬁ g. 4)

NOTE: For best results, make sure your battery

pack is fully charged. The light will shut off without

warning when the battery is fully discharged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the battery pack (b) with the rails inside the

tool’s handle (fig. 4).

2. Slide it into the handle until the battery pack is

firmly seated in the tool and ensure that it does

not disengage.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the battery release button (a) and firmly

pull the battery pack out of the tool handle.

2. Insert battery pack into the charger as

described in the charger section of this manual.

Blade Installation and Removal

(ﬁ g. 6)

TO INSTALL A BLADE

NOTE: This jig saw uses only T-shank jig saw

blades.

NOTE: The DT2074 flush cutting blade is for use

with DEWALT DCS331, DCS332, DW331 and

DC330 jig saws only.

NOTE: When installing flush cutting blades

(DT2074), the anti-splinter insert must be removed

and the shoe must to be in the 0° positive stop

position.

1. Lift the keyless blade release lever (e) as shown

in figure 6.

2. Insert the T-shank blade into the clamp

mechanism (k) while guiding the back of the

blade into the groove of the guide rollers (l).

3. The T-shank should be completely inside the

clamp mechanism as shown in Figure 6.

4. Release the keyless blade release lever.

TO REMOVE A BLADE

CAUTION: Do not touch used blades,

they may be hot. Personal injury may

result.

1. Lift the keyless blade release lever (e).

2. With a slight shake the blade will drop out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCS331 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info