Bedienungsanleitung DeWalt DCT410 T 1 (Seite 43 von 204) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

548898

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

ENGLISH

Camera Cable (ﬁ g. 5)

Align the camera cable (c) with the camera

connector (d). Push in and turn the connector

counterclockwise (camera screen facing you) to

firmly attach.

To remove the camera cable, turn the connector

clockwise (direction of arrow).

Additional camera cable and extensions are available

at additional cost. Consult your dealer for further

information.

Hook and Magnet (ﬁ g. 6)

DCT410

The hook is beneficial for retrieving cable or wire

located in tight spaces. The magnet is beneficial for

retrieving metal objects in tight spaces.

To attach the hook or magnet, turn the knurled part

of the camera counterclockwise until it stops.

Align the hook or magnet with the gray groove (t)

then slide it down until the tabs (u) at the top of the

hook/magnet are securely in the notches (v) located

in the camera lens.

Turn the knurled part clockwise to lock the base of

the hook and magnet.

Hook, Magnet and Mirror (ﬁ g.7,8)

DCT411

Follow the process below to assemble the hook,

magnet or mirror onto the DCT411 9mm camera.

1. With the sleeve (w) on the accessory, insert the

bottom of accessory (bent wire) into the hole (x)

in the 9mm camera cable.

2. Make sure the accessory is in the groove (y) on

the sleeve and slide the sleeve onto the camera

until the sleeve covers the hole(x).

CAUTION: Cut Hazard. Use care when

handling hook.

Belt Hook (ﬁ g. 9)

(Optional Accessory)

WARNING: To reduce the risk of

serious personal injury, DO NOT

suspend camera overhead or suspend

objects from the belt hook. ONLY hang

camera’s belt hook from a work belt.

WARNING: To reduce the risk of

serious personal injury, ensure the

screw (z) holding the belt hook is

secure.

IMPORTANT: When attaching or removing the belt

hook, use only the screw (z) that is provided.

The belt hook (aa) can be attached to either side

of the tool using only the screw (z) provided, to

accommodate left- or right-handed users. If the

hook is not desired at all, it can be removed from

the tool.

To move belt hook, remove the screw (z) that holds

the belt hook in place then reassemble on the

opposite side.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

Inserting and Removing the

Battery Pack from the Inspection

Camera (ﬁ g. 10)

NOTE: Make sure your battery pack (a) is fully

charged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the battery pack with the rails inside the

handle.

2. Slide it firmly into place until you hear the lock

snap into place.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the release button (bb) and firmly pull the

battery pack out of the camera handle.

2. Insert battery pack into the charger as

described in the charger section of this manual.

Getting Started

INITIAL SETUP

Language Setup

1. Press the forward or back arrow to select

English, German, Spanish, French, Italian or

Dutch.

2. Press the OK button to confirm and exit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCT410 T 1 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DCT410 T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info