Bedienungsanleitung DeWalt DW 226 (Seite 25 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78845

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH

- Alert mode: if the indicator flashes repeatedly,

the electronics do not function properly. Take

your tool to an authorized DEWALT repair agent.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

In case of cord replacement the tool must only

be repaired by an authorized service agent or by

qualiﬁ ed electrician.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the

plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made

to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

WARNING: 115 V units have to

be operated via a fail-safe isolating

transformer with an earth screen between

the primary and secondary winding.

Using an Extension Cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data). The minimum conduc tor

size is 1.5 mm

. When using a cable reel, always

unwind the cable completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-ups

or when making repairs. Be sure the

trigger switch is in the OFF position. An

accidental start-up can cause injury.

Inserting and Removing a Bit (ﬁ g. A, B)

• Open the chuck by turning the sleeve

counterclockwise and insert the bit shank.

• Tighten ﬁ rmly by turning the sleeve clockwise.

• To remove the bit, proceed in reverse order.

DW221/DW226/DW236/DW246/DW248 -

Spindle Lock

These models have a spindle lock button (4).

• Depress the spindle lock button to lock the

chuck while inserting or removing a bit.

WARNING: Never depress the spindle

lock button during operation.

Forward/reverse Slider (ﬁ g. C)

• To select forward or reverse rotation, use the

forward/reverse-switch (3) (see arrow on tool).

WARNING: Always wait until the motor

has come to a complete standstill before

changing the direction of rotation.

Chuck Removal (ﬁ g. E & F)

• Open the chuck jaws as far as possible.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw (8) by turning

clockwise.

• Tighten an Allen key into the chuck and strike it

with a hammer as shown.

Prior to Operation

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

OPERATION

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Instructions for Use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework

and wiring.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW 226 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info