Bedienungsanleitung DeWalt DW 304 (Seite 17 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

110192

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

Package contents

The package contains:

1 Reciprocating saw

1 General purpose saw blade set

1 Kitbox (K-models only)

1 Instruction manual

1 Exploded drawing

● Check for damage to the tool, parts or accessories which may have

occurred during transport.

● Take the time to thoroughly read and understand this manual prior to

operation.

Description (ﬁ g. A)

Your DW304 reciprocating saw has been designed for professional

sawing of wood, metal and tubes. The compact design permits cutting

extremely close to the edge of difﬁ cult areas.

1 Variable speed switch

2 Blade clamp lever

3 Saw shoe

Electrical safety

The electric motor has been designed for one voltage only. Always

check that the power supply corresponds to the voltage on the rating

plate.

Your D E WALT tool is double insulated in accordance with

EN 60745; therefore no earth wire is required.

115 V units have to be operated via a failsafe isolating

transformer with an earth screen between the primary and

secondary winding.

Mains plug replacement

(U.K. & Ireland only)

● Should your mains plug need replacing and you are competent to do

this, proceed as instructed below. If you are in doubt, contact an

authorized D E WALT repair agent or a qualiﬁ ed electrician.

● Disconnect the plug from the supply.

● Cut off the plug and dispose of it safely; a plug with bared copper

conductors is dangerous if engaged in a live socket outlet.

● Only ﬁ t 13 Amperes BS1363A approved plugs ﬁ tted with the correctly

rated fuse (1).

● The cable wire colours, or a letter, will be marked at the connection

points of most good quality plugs. Attach the wires to their respective

points in the plug (see below). Brown is for Live (L) (2) and Blue is for

Neutral (N) (4).

● Before replacing the top cover of the mains plug ensure that the

cable restraint (3) is holding the outer sheath of the cable ﬁ rmly and

that the two leads are correctly ﬁ xed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N) wires to the earth

pin marked E or .

For 115 V units with a power rating exceeding 1500 W, we recommend

to ﬁ t a plug to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved extension cable

suitable for the power input of this machine (see technical data). The

minimum conductor size is 1.5 mm

. The cable has to have a rubber

jacket and a grounding conductor.

When using a cable reel, always unwind the cable completely.

Also refer to the table below.

CONDUCTOR SIZE (MM

) CABLE RATING (AMPERES)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

CABLE LENGTH (M)

7.5 15 25 30 45 60

VOLTAGE AMPERES CABLE RATING (AMPERES)

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always unplug the tool.

Mounting the saw blade (ﬁ g. B)

● Move the blade clamp lever (2) up to release the blade clamping

mechanism.

● Insert the saw blade into the holder (4) until it engages. The blade

can be installed with the teeth pointing down or up, or left or right.

● Move the blade clamp lever (2) down to lock the blade clamping

mechanism.

● To remove the saw blade, proceed in reverse order.

Saw blades

material recommended saw blade

ferrous metal ﬁ ne-toothed

non ferrous metal coarse-toothed

wood coarse-toothed

plastic ﬁ ne-toothed

masonry carbide-tipped

A wide variety of dedicated saw blades is available as an option.

Always select your saw blade with great care.

Instructions for use

● Always observe the safety instructions and applicable

regulations.

● Ensure the material to be sawn is secured in place.

● Apply only a gentle pressure to the tool and do not exert side

pressure on the saw blade. If possible, work with the saw

shoe pressed against the workpiece. This prevents damage

to the blade and stops the tool from jerking and vibrating.

● When sawing in walls or ﬂ oors be aware of the location of

pipework and wiring. Always hold the tool by its handle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW 304 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info