Bedienungsanleitung DeWalt DW 333 (Seite 32 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

110161

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

ENGLISH

• For continuous operation, press and hold down

the switch (1), press the lock-on button (2) and

release the switch.

• To stop the tool, release the switch.

• To stop the tool in continuous operation, press

the switch briefly and release it. Always switch

off the tool when work is finished and before

unplugging.

DW333

• Switching on: slide the on/off switch (1) to the front.

• Switching off: slide the on/off switch to the rear.

Always switch off the tool when work is finished

and before unplugging.

Setting the electronic sawing speed

(ﬁ g. G1 & G2)

DW331 (fig. G1)

The sawing speed varies with the pressure exerted

on the on/off switch (1).

• To preset the sawing speed, turn the control dial

(3) to the desired level. The higher the rate, the

higher the sawing speed. The required setting

depends on the thickness and kind of material.

• Use high speeds for sawing soft materials such

as wood. Use low speeds for sawing metal.

DW333 (fig. G2)

The speed control dial (3) can be used for advance

setting of the required range of speed.

• Turn the electronic speed control dial to the

required level. The required setting depends on

the thickness and kind of material.

• Use high speeds for sawing soft materials such

as wood. Use low speeds for sawing metal.

WARNING: After using the tool for

an extended period on low speed

settings, run it for approx. 3 minutes on

maximum no-load speed.

Sawing in wood

• If necessary, draw a cutting line.

• Switch the tool on.

• Hold the tool against the workpiece and follow

the line.

• For sawing parallel to the edge of your workpiece,

install the parallel fence and guide your jigsaw

along the workpiece a shown in figure H.

Sawing in wood using a pilot hole

• If necessary, draw a cutting line.

• Drill a hole (ø min. 12 mm) and introduce the saw

blade.

• Switch the tool on.

• Follow the line.

• For cutting perfectly round shapes, install the

trammel bar and set it to the required radius (fig. I).

Sawing up to a projecting edge (fig. J)

• Using a conventional blade, cut up to the

projected edge.

• Finish off the cut using a flush cutting blade.

Dust extraction (fig. F)

• When the tool is used indoor for extended

periods of time, use a suitable dust extractor

designed in compliance with the applicable

Directives regarding dust emission.

Sawing in metal

• Mount an appropriate saw blade.

• Proceed as described above.

WARNING: Use a cooling lubricant

(cutting oil) to prevent overheating of the

saw blade or the workpiece.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing

set-ups or when making repairs.

Be sure the trigger switch is in the OFF

position. An accidental start-up can

cause injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW 333 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info