Bedienungsanleitung DeWalt DW 443 (Seite 28 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

78278

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH

Proper Hand Position (ﬁ g. 1, 7)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (f), with the other hand on the main handle (j).

Sanding (ﬁ g. 1)

This random orbit sander produces small scratch

marks in all directions. Therefore, it is not necessary

to sand with the grain.

1. If necessary, fit the side handle (f).

2. Set the sanding speed using the electronic

speed control dial (b).

3. Turn the sander on using the on/off switch (a).

I = on

O = off

4. Start with the coarsest grit size.

5. Check your work at short intervals.

6. Always switch off the tool when work is finished

and before unplugging.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Replacing the Sanding Pad and the

Speed Limiter Disc (ﬁ g. 6)

Both the sanding pad (h) and the speed limiter disc

(m) are consumable parts. The sanding pad needs

replacement when signs of wear become evident.

The speed limiter disc needs replacement when the

sanding pad speed increases dramatically when

lifting the sander off the workpiece.

1. Unplug the tool.

2. Loosen the 4 hex head screws (n) and remove

the pad.

3. Replace the sanding pad (h) and/or speed

limiter disc (m) and tighten the Hex head screws

(n), making sure the speed limiter disc is aligned

properly.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

Optional Accessories

WARNING: Since accessories, other

than those offered by DEWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only DEWALT, recommended

accessories should be used with this

product.

Consult your dealer for further information on the

appropriate accessories.

Protecting the Environment

Separate collection. This product must

not be disposed of with normal

household waste.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW 443 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info