Bedienungsanleitung DeWalt dw 492 (Seite 25 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

390424

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

• Mount the round handle (22) using the two

screws (23).

• Fit one screw in the top hole (7) and the other in

one of the side holes (8).

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the tool.

Do not exert side pressure on the

grinding wheel or cutting disc.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the spacer and threaded flange are

mounted correctly.

• Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and the

tool.

Switching on and off (fig. A)

The on/off-switch of your angle grinder is equipped

with an unlocking switch or a locking switch for

continuous operation.

(U.K. & France only) - On/off-switch (1) with

unlocking switch (2)

• To unlock the on/off-switch, slide the unlocking

switch towards you.

• To run the tool, press the on/off-switch.

• To stop the tool, release the on/off-switch.

On/off-switch (1) with locking switch (2a)

• To run the tool, press the on/off-switch. The tool

now runs in continuous operation.

• To stop the tool, press the locking switch briefly,

and release the on/off-switch.

Do not switch the tool on or off when

under load.

ENGLISH

DW491 - Using the diamond guard DE8501

(option) (fig. C)

The diamond guard is used for cutting concrete and

masonry, when accurate cutting depth adjustment

or dust extraction are required.

• Mount the diamond guard as described above.

• Connect a dust extractor to the outlet (17).

• Set the cutting depth using the ruler knob in the

front plate (13).

• Observe the safety instructions applying

to diamond cutting discs.

• Use a suitable diamond cutting disc

(check the data of the manufacturer).

• The maximum rotation speed on the cutting

disc must not be lower than that of the tool.

• Do not use cutting discs with a diameter

exceeding 230 mm.

Fire hazard! Do not use the dust

extractor when cutting metal!

Make sure that the dust extractor used is

suitable for the material to be cut and the

Diamond guard can be connected.

DW491 - Using the round handle DE8502

(option) (fig. F)

The round handle provides greater convenience and

makes your tool very easy to handle.

• Mount the round handle as described above.

Consult your dealer for further information on the

appropriate accessories.

DWLAG.P65 17-09-2001, 08:4925

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dw 492 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt dw 492

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info